I still get stuff on the old list also. I like the glue discussion. Hey how does molding and trim glue fit into the picture. It' my glue of choice on a lot of stuff---including hammer hanging if for some reason hot hide is not handy, etc. (However, on WNG carbon fiber shanks, I don¹t' think I would use anything other than the special super glue they supply.) I had some FANTASTIC results yesterday voicing a Baldwin Hamilton in one of our small classrooms. Needed to do an emergency "bring the hammers down out of the rafters" voicing so that one of our Opera profs could do a quick jury in this room at the last minute. I decided to chuck up a #2 crewel needle in my battery powered dremel tool--about and inch/inch and 1/4 in length. (Big honking needle--I proceeded with MUCH, MUCH caution.) I tried angel shot from several different angle, going straight down through the shoulder and went all the way through to the other shoulder--voicing on the side, etc. etc. (these may be the only hammers known to man that need this type of POWER NEEDLING!!) After a while I developed a FAIRLY good routine & was able to bring the mid range down to about where the bass was with PRETTY GREAT sound and evenness--and then just brought the worst of the treble down to get a fairly good progression. I think I am on to something here. We have like a KA-BILLION of these Hamiltons here at Texas Tech. And like 90 % of them MUST BE BROUGHT down and w/o spending a ton of time. I will do further research--of course all voicing is somewhat experimental! I have also been wanting to share about our INCREDIBLE new Fazioli 278 (the 9'2" one. Does not have the fourth pedal.) Our piano faculty is particularly excited about this piano--as are so many here in the School of Music. I LOVE tuning and voicing this piano. Of couse the voicing on this piano is DIAMETRICALLY OPOSED to the Hamilton type above. I have found that I really do LIKE filing the hammers with the narrow strips of 600 grip wet dry, 1000, grit and even 1500 grit--still put masking tape on the back. For regular needling these hammer are a dream. They voice much like the regular Renners, except VERY RESPONSIVE! There are several tricks the guy from the piano dealer in New York showed me (actually Sujatri is from Italy, and is part owner of the Clavierhouse dealer.), but Fred had done a wonderful job of desribing the Fazioli methods. I am looking forward to learning much more about this--and the lines drawn on the hammers. Fantastic piano! Kevin Fortenberry On 5/11/12 9:09 AM, "caut-request at ptg.org" <caut-request at ptg.org> wrote: >Send CAUT mailing list submissions to > caut at ptg.org > >To subscribe or unsubscribe via the World Wide Web, visit > https://www.moypiano.com/resources/#archives >or, via email, send a message with subject or body 'help' to > caut-request at ptg.org > >You can reach the person managing the list at > caut-owner at ptg.org > >When replying, please edit your Subject line so it is more specific >than "Re: Contents of CAUT digest..." > > >Today's Topics: > > 1. Re: test (Richard West) > 2. Re: test (Norman Cantrell) > 3. Re: test (Richard West) > 4. Re: test (James Schmitt) > 5. Re: test (Paul Williams) > 6. Re: [pianotech] Shank glue (Richard Murphy) > > >---------------------------------------------------------------------- > >Message: 1 >Date: Fri, 11 May 2012 07:19:39 -0500 >From: Richard West <rwest1 at unl.edu> >To: caut at ptg.org >Subject: Re: [CAUT] test >Message-ID: <2E445663-E398-45E2-9914-16AE3D0CDE17 at unl.edu> >Content-Type: text/plain; charset=iso-8859-1 > >I'm testing to see if I can get to the old CAUT list. > >Richard West > > >------------------------------ > >Message: 2 >Date: Fri, 11 May 2012 06:04:18 -0700 (PDT) >From: Norman Cantrell <normancantrell at sbcglobal.net> >To: caut at ptg.org >Subject: Re: [CAUT] test >Message-ID: > <1336741458.67562.YahooMailClassic at web83905.mail.sp1.yahoo.com> >Content-Type: text/plain; charset="us-ascii" > >Richard >Yes you can but I forgot to study for your test. >Norman Cantrell > >--- On Fri, 5/11/12, Richard West <rwest1 at unl.edu> wrote: > >From: Richard West <rwest1 at unl.edu> >Subject: Re: [CAUT] test >To: caut at ptg.org >Date: Friday, May 11, 2012, 7:19 AM > >I'm testing to see if I can get to the old CAUT list. > >Richard West >-------------- next part -------------- >An HTML attachment was scrubbed... >URL: ><https://www.moypiano.com/ptg/caut.php/attachments/20120511/95d6d4a0/attachme >nt-0001.htm> > >------------------------------ >
This PTG archive page provided courtesy of Moy Piano Service, LLC