Side cutter

[DICK BEATON]

Hi all...
I've been watching the side cutter thread.  A good inexpensive side cutter
can be had from Radio Shack.  It is the pliar used to cut the component
ends off the back side of a circuit board after the soldering is done. 
They work great...just don't use them for anything else.
Dick RPT MT

----------
> From: Barrie Heaton <Piano@forte.airtime.co.uk>
> To: pianotech@ptg.org
> Subject: Re: Side cutter
> Date: Monday, February 02, 1998 2:27 AM
> 
> Hi Howard,
> 
> No joy!  they do not stock them now, they stock a USA product which he
> said is "not much cop" :-(
> 
> Fletcher Stock a good quality flush cutter price £15.00  
> cat number 584a  
> Tel: 44 1322226441  Fax 44 1322278978
> 
> The man said that they were a German equivalent to the Bahco.
> 
> 
> Barrie
> 
> 
> 
> In article <199801301705.MAA12387@emi.net>, "Howard S. Rosen"
> <hsrosen@emi.net> writes
> >Hi Barrie,
> >
> >I went to the website you suggested and found center pin cutter #194 but
> >could not find the price nor any other particulars. I don't know if it's
> >the Bahco 22215 that you recommended. HELP!
> >
> >Howard S. Rosen, RPT
> >Boynton Beach, Florida
> >
> >----------
> >> From: Barrie Heaton <Piano@forte.airtime.co.uk>
> >> To: pianotech@ptg.org
> >> Subject: Re: Side cutter
> >> Date: Thursday, January 29, 1998 1:04 PM
> >> 
> >> I use Bahco 22215 made in Sweden  I have had them since 1977 and still
> >> as good as new. I hevw done a lot of re-centering.
> >> 
> >> I think you can still get them from Heckschers UK
> >> 
> >> Tel: 44  173871735
> >> Fax  443873043
> >> 
> >> 
> >> Web site. www.airtime.co.uk/forte/heckscher/
> >> 
> >> Barrie,
> >> 
> >> 
> >> In article <01bd2b18$d1a801a0$0100007f@localhost>, Michiel van Loon
> >> <mvanloon@xs4all.nl> writes
> >> >Dear list,
> >> >
> >> >Can somebody please tell me what is the best tool for cutting center
> >pins.
> >> >My pianosuplyhouse always sold "Bletzer" as they where the best.
> >> >But the Beltzer cutters of that quality are not made anymore.
> >> >I now use a "Snap on" electronics side cutter E710ACG, but I'm not
quite
> >> >satisfied with it.
> >> >
> >> >Regards,
> >> >Michiel van Loon
> >> >Meppel
> >> >Nederland
> >> >http://www.xs4all.nl/~mvanloon
> >> >tel/fax ++31 522 255160
> >> >
> >> >
> >> 
> >> 
> >> 
> >> 
> >> 
> >> --
> >> 
> >> Barrie Heaton                                  |  Be Environmentally
> >Friendly
> >> URL: http://www.airtime.co.uk/forte/piano.htm  |  To Your Neighbour
> >> The UK PIano Page                              |  
> >> pgp  key on request                            |  HAVE YOUR PIANO
TUNED
> >
> 
> 
> 
> 
> 
> --
> 
> Barrie Heaton                                  |  Be Environmentally
Friendly
> URL: http://www.airtime.co.uk/forte/piano.htm  |  To Your Neighbour
> The UK PIano Page                              |  
> pgp  key on request                            |  HAVE YOUR PIANO TUNED
>