Steinway piano, you can't pull the action rail. David Love davidlovepianos at comcast.net -----Original Message----- From: pianotech-bounces at ptg.org [mailto:pianotech-bounces at ptg.org] On Behalf Of Andrew and Rebeca Anderson Sent: Friday, May 26, 2006 3:07 PM To: Pianotech List Subject: RE: Clicking drop screws on a new Steinway Fired off too early in the morning. Yes drop screws are on the hammer flange and pulling that action rail would allow you to glue with ease without fear of leaks. Seems those screws should be tough enough to take CA. Good luck, Andrew At 08:33 AM 5/26/2006, you wrote: Not sure how this relates. Which rail are we talking about? It's the drop screws that are loose, not the let-off buttons. The piano is in a medium to high humidity environment (50 - 65% on average). David Love davidlovepianos at comcast.net -----Original Message----- From: pianotech-bounces at ptg.org [ <mailto:pianotech-bounces at ptg.org> mailto:pianotech-bounces at ptg.org] On Behalf Of Andrew and Rebeca Anderson Sent: Friday, May 26, 2006 6:03 AM To: Pianotech List Subject: RE: Clicking drop screws on a new Steinway David, I was going to ask about the climate the piano is in now with several items loose. With the details it looks more like a mixed bag. The Steinway parts list has this: 005151 ACTION FRAME LETOFF RAIL BORED - A/B EA 54.00 There is another part that includes the buttons for more but labor costs too! 009073 ACTION FRAME W/LETOFF BUTTONS - A/B EA 292.00 You are still stuck with regulating them all into position but that does make more sense than running all the old ones out of the old rail and then into the new rail. I haven't tried it, but removing the rail and running thinned lacquer down by all the screws might tighten things up and weatherize the wood. Perhaps it won't flow in easily. I'd be worried about broken drop screws with CA (I'd definitely remove the rail for a CA treatment too). Keep us apprised of the solution and then how it holds up. Andrew Anderson At 11:34 PM 5/25/2006, you wrote: Yes, I do understand the word warranty and at this point it's not a question of warranty or not. It's getting fixed and because my customer insisted on it as part of the terms of the sale, the dealer is paying me to do the fixes (of course, they haven't sent me a check yet). Whether it's warranty or dealer prep or anything else, it still has to be fixed. The fixes will be based on my recommendations and I'm looking for something short of rehanging hammers on new shanks or replacing wippens that might have the same problem. The piano was "prepped" as it were, and so far I've had to ease the jack pinning, repin all the hammer flanges, remove, polish and realign the damper wires to reduce noise and drag, ease the guide rail bushings, increase the dip so I didn't have to set the blow at 37 mm to get any aftertouch (not many leads in this action though). Still have a few buzzes and whistles to deal with, the treble side of the action is moved in too far (strike point is correct) and it's creating a small problem getting the una corda to shift quietly (but at least the sharps aren't knocking against the fallboard). You know, normal stuff. David Love davidlovepianos at comcast.net -----Original Message----- From: pianotech-bounces at ptg.org [ mailto:pianotech-bounces at ptg.org] On Behalf Of Erwinspiano at aol.com Sent: Thursday, May 25, 2006 8:55 PM To: pianotech at ptg.org Subject: Re: Clicking drop screws on a new Steinway HI David In the spirit of Jon Pages post. Our new word for today is W-A-R-R-A-N-T-Y. Repeat after me boys & girls...... warranty. A 70 k piano has Warr....an....ty. Pinning the shanks!! Clicking drop screws. I suggest a phone call to the factory yes ir ee. Perhaps the remedy is to buy German. They seem to have gotten it right Dale Re your other message, it is disturbing (actually the piano costs $70,000). The shanks require repining (all of them were way too loose), and many jacks required easing as they were too tight. It's why I've given up on their parts. David Love davidlovepianos at comcast.net Dale Erwin--Piano Restorations 4721 Parker Rd. Modesto, Calif. 95357 Shop 209-577-8397 cell 209-985-0990 Web site http://www.Erwinspiano.com <http://www.erwinspiano.com/> Specializing in the Restoration, Service & Sales of Steinway & Sons, Mason & Hamlin, & other fine pianos -------------- next part -------------- An HTML attachment was scrubbed... URL: https://www.moypiano.com/ptg/pianotech.php/attachments/20060526/9f35f157/attachment.html
This PTG archive page provided courtesy of Moy Piano Service, LLC