Terry ? Got it. Diagonal It was an interesting cut. I had to modulate the guides as I went. You know...When the machine is cuttin perfect you can do no wrong...when it's not it makes you an idiot!? Kind of like women. Never mind ?Dale Thanks Dale. Reasonable approach on the diagonal cut. However, the straight cut gives the additional advantage of keeping the bandsaw upper guide blocks right at the top of the wood being sawed over the entire cut?- just a better chance for a perfectly (or nearly so) straight cut. I was starting this with a blade that already had some miles on it - but still performed admirably. ? I haven't used #2 pins in one of these blocks - only #1 pins. And I honestly don't remember what my final bit size was. I do the Ron N two pass drilling method and I simply always drill a few holes in the block in an area outside the tuning pin fields and pound in?a few pins for testing - I just always feel better doing that. ? Terry Farrell ----- Original Message ----- From: erwinspiano at aol.com To: pianotech at ptg.org Sent: Sunday, January 04, 2009 11:47 PM Subject: Re: [pianotech] Double-Wides ? Hi Terry ? On my Last double wide block I confronted the same issues as you describe here so?my solution was to just cut the delignit block at a diagonal angle & then resaw?so each piece was equal & in the same shape roughly as? a single block. ie wider on one end & narrow on the other. However with a good glue joint doing it?as you describe should be? of no concern. ?With what size drill bit do you recommend on this type block for no.2 pins ? ? Well Done ? Dale ? No, not those - but rather pinblocks - and more specifically, Delignit capped Multilam doublewides. ? Yup, made up my first doublewide Delignit capped Multilam pinblock this weekend. Client of mine has two large pianos to rebuild and after going back and forth on dimensions?we both realized it would be a lot easier if I were to simply make him up a doublewide pinblock blank. So here it is! ? ? ? Full double-width. The Delignit blanks are an inch or so larger than the Multilam - so the final capped block is the size of the original Multilam double blank. ? ? ? Even though I have a very nice bandsaw, it can't resaw an 18-inch wide (tall) piece of laminated European Beech. So?I cut?the double-wide Delignit blank?in half and resawed the?halves. The?Delignit cap on my pinblock blank ends up with a joint running down the middle - but it's a nice tight joint - one should have no concern even if a tuning pin were to bisect the joint. ? ? Blatant commercial ploy: operators are standing by.......? ;-) ? Terry Farrell Farrell Piano, Inc. ? www.farrellpiano.com terry at farrellpiano.com Get a free MP3 every day with the Spinner.com Toolbar. Get it Now. -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://ptg.org/pipermail/pianotech_ptg.org/attachments/20090105/5581436f/attachment-0001.html> -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/jpeg Size: 41112 bytes Desc: not available URL: <http://ptg.org/pipermail/pianotech_ptg.org/attachments/20090105/5581436f/attachment-0003.jpe> -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/jpeg Size: 52525 bytes Desc: not available URL: <http://ptg.org/pipermail/pianotech_ptg.org/attachments/20090105/5581436f/attachment-0004.jpe> -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/jpeg Size: 43419 bytes Desc: not available URL: <http://ptg.org/pipermail/pianotech_ptg.org/attachments/20090105/5581436f/attachment-0005.jpe>
This PTG archive page provided courtesy of Moy Piano Service, LLC