It is a beautiful piece of machinery. Any technical data...pictures of it being used etc? Real world use...get that camera out, Marco... David Ilvedson, RPT Pacifica, CA 94044 ----- Original message ---------------------------------------- From: "piano workshop" <info at pianoworkshopny.com> To: al at pebworths.com; pianotech at ptg.org Received: 5/3/2009 5:38:37 AM Subject: Re: [pianotech] Renner hammer boring jig >Hi Al, >I believe they are two different thing >Marco De Lellis >Piano Workshop Inc. >PTG - Registered Piano Technician >21-05 31st. Avenue >Astoria New York, 11106 >USA >tel. 001 212 575 4949 >tel. 001 718 956 3110 >www.pianoworkshopny.com >info at pianoworkshopny.com > > _____ >From: pianotech-bounces at ptg.org [mailto:pianotech-bounces at ptg.org] On Behalf >Of Al Pebworth >Sent: Saturday, May 02, 2009 9:07 PM >To: pianotech at ptg.org >Subject: Re: [pianotech] Renner hammer boring jig > >Hello Marco, >Are we talking about the same boring jig? The one I use and the link I >posted was for a jig purchased from Lloyd Meyer at Renner USA. It is still >in their catalog. >http://www.lloydmeyer.com/productcart/pc/viewPrd.asp?idcategory=8 ><http://www.lloydmeyer.com/productcart/pc/viewPrd.asp?idcategory=8&idproduct >=26> &idproduct=26 >Al >Al Pebworth >Chesapeake, Virginia >--- On Sat, 5/2/09, piano workshop <info at pianoworkshopny.com> wrote: >From: piano workshop <info at pianoworkshopny.com> >Subject: Re: [pianotech] Renner hammer boring jig >To: pianotech at ptg.org >Date: Saturday, May 2, 2009, 3:32 PM >Nobody sell this machine here > in USA. >You can contact jahn >Jahn > >Manufacturers of Piano Parts >Alfred Jahn, D-96271 Grub am Forst, Germany >95 60/80 34 >Fax: 95 60/17 34 >I can do better in this monday > >Or FTP in Italy at 011 39 0444 288725 > >If you have a problem contact me > >Marco De Lellis >Piano Workshop Inc. >PTG - Registered Piano Technician >21-05 31st. Avenue >Astoria New York, 11106 >USA >tel. 001 212 575 4949 >tel. 001 718 956 3110 >www.pianoworkshopny.com >info at pianoworkshopny.com > > >-----Original Message----- >From: pianotech-bounces at ptg.org [mailto:pianotech-bounces at ptg.org] On Behalf >Of Gene Nelson >Sent: Saturday, May 02, 2009 2:49 PM >To: pianotech at ptg.org >Subject: Re: [pianotech] Renner hammer boring jig > >Hello Marco, >Does Jahn have a catalog? Are these jigs available in the U.S.? >Thanks, >Gene >----- Original Message ----- >From: "piano workshop" > <info at pianoworkshopny.com> >To: <pianotech at ptg.org> >Sent: Saturday, May 02, 2009 10:01 AM >Subject: Re: [pianotech] Renner hammer boring jig > > >> This is the right boring machine ever...for my opinion. >> It's expensive but do is job accurately. >> These machine its Made in Italy but sold by Jahn - Germany. >> I work with it more than 10 years without any problem. >> Easy to set easy to use. >> >> Marco De Lellis >> Piano Workshop Inc. >> PTG - Registered Piano Technician >> 21-05 31st. Avenue >> Astoria New York, 11106 >> USA >> tel. 001 212 575 4949 >> tel. 001 718 956 3110 >> www.pianoworkshopny.com >> info at pianoworkshopny.com >> >> >> -----Original Message----- >> From: pianotech-bounces at ptg.org [mailto:pianotech-bounces at ptg.org] On >> Behalf >> Of Mark Dierauf >> Sent: Saturday, May 02, 2009 9:32 AM >> > To: Pianotech >> Subject: [pianotech] Renner hammer boring jig >> >> Does anybody know if this jig will bore vertical hammers as well as >> grands? I'm particularly wondering if it is capable of boring the >> extreme rake angle found on the old S&S uprights. Thanks, >> >> - Mark >> >> >> >> >> > > > > > > >
This PTG archive page provided courtesy of Moy Piano Service, LLC