<HTML><BODY style="word-wrap: break-word; -khtml-nbsp-mode: space; -khtml-line-break: after-white-space; ">Reading all of these posts....and now this about having to grow new skin to cover the stain it'll make??? * what is the point of this stuff?*<DIV>Should we even have it in the shop?</DIV><DIV>I vote no.</DIV><DIV> </DIV><DIV>(I *do* have a very small bottle at home but I have not yet used it. Don't know if I will..)</DIV><DIV> </DIV><DIV>JMHO... <DIV><DIV>On Nov 9, 2006, at 1:40 PM, Richard Murphy wrote:</DIV> <BLOCKQUOTE type="cite"> HI Don, Be careful not to get any on your skin because it will stain your fingers brown and it doesn’t wash off, you have to wait until your fingers grow new skin (about 1 1/2 to 2 weeks). You put the glue on one surface and wet the other with water, then fit the parts together and clamp them strongly because the glue foams up and will push the two pieces apart. You will have to clean up the foam from the outside afterwards. Definitely not the glue to use on parts that need replacing. Richard On 11/9/06 10:31 AM, "Wigent, Donald E" <<A href="mailto:WIGENTD@ecu.edu">WIGENTD@ecu.edu</A>> wrote: <BLOCKQUOTE type="cite">Say gang: tell me about this glue, Can I handle it or is it like CA and would it be good for cracked bridges. What is it good for? Maybe broken leggs or ripped out lid hinges? Don Wigent E C U <DIV align="CENTER"> <HR align="CENTER" size="2" width="100%"> </DIV><DIV> From: <A href="mailto:caut-bounces@ptg.org">caut-bounces@ptg.org</A> [<A href="mailto:caut-bounces@ptg.org]">mailto:caut-bounces@ptg.org]</A> On Behalf Of Jim Busby Sent: Wednesday, November 08, 2006 1:31 PM To: College and University Technicians Subject: Re: [CAUT] gorilla glue Thanks Dale. Of course, I was hoping you’d have some magic solvent or voodoo for me. What an awful glue… Jim Busby BYU </DIV><DIV align="CENTER"> <HR align="CENTER" size="2" width="100%"> </DIV><DIV> From: <A href="mailto:caut-bounces@ptg.org">caut-bounces@ptg.org</A> [<A href="mailto:caut-bounces@ptg.org]">mailto:caut-bounces@ptg.org]</A> On Behalf Of Ward & Probst, Inc Sent: Wednesday, November 08, 2006 10:15 AM To: 'College and University Technicians' Subject: Re: [CAUT] gorilla glue Jim, I think you'll have to cut the hammers off to save the shanks. I'd use a band saw to remove as much as possible. then whittle off the rest. I am pretty sure that poly glue is not susceptible to solvents after it sets. All that said, you'd have enough time in the job to have to weigh it against the cost of new parts, particularly if the original parts need repining, etc. I'd guess it'd would take two to three hours to clean up the old shanks. Unless they are unusual or costly shanks, that would be at least half the way to new parts. Good luck, Dale Dale E. Probst, RPT Ward & Probst, Inc. Wichita Falls, TX <A href="mailto:dale@wardprobst.com">mailto:dale@wardprobst.com</A> www.wardprobst.com <A href="http://www.wardprobst.com/"><http://www.wardprobst.com/></A> </DIV><BLOCKQUOTE type="cite">-----Original Message----- From: <A href="mailto:caut-bounces@ptg.org">caut-bounces@ptg.org</A> [<A href="mailto:caut-bounces@ptg.org]">mailto:caut-bounces@ptg.org]</A> On Behalf Of Jim Busby Sent: Wednesday, November 08, 2006 10:36 AM To: College and University Technicians Subject: [CAUT] gorilla glue List, All the talk of glue brings me to this problem/question. Someone used gorilla glue to hang some hammers that I want to remove and I can’t find ANYTHING that will work. I know I could simply buy new shanks and flanges, but does anyone know of anything that’s works on this stuff?? Thanks. Jim Busby BYU </BLOCKQUOTE> </BLOCKQUOTE> </BLOCKQUOTE></DIV> </DIV></BODY></HTML>