<html xmlns:v="urn:schemas-microsoft-com:vml" xmlns:o="urn:schemas-microsoft-com:office:office" xmlns:w="urn:schemas-microsoft-com:office:word" xmlns:st1="urn:schemas-microsoft-com:office:smarttags" xmlns="http://www.w3.org/TR/REC-html40"> <head> <META HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=us-ascii"> <meta name=Generator content="Microsoft Word 11 (filtered medium)">  <title>Message</title> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="State"/> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="City"/> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="place"/> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="PersonName"/>  <style>  </style>  </head> <body lang=EN-US link=blue vlink=purple> <div class=Section1> Say gang: tell me about this glue, Can I handle it or is it like CA and would it be good for cracked bridges. What is it good for? Maybe broken leggs or ripped out lid hinges? <o:p></o:p> Don Wigent<o:p></o:p> E C U<o:p></o:p> <o:p> </o:p> <div> <div class=MsoNormal align=center style='text-align:center'> <hr size=2 width="100%" align=center tabindex=-1> </div> From: caut-bounces@ptg.org [mailto:caut-bounces@ptg.org] On Behalf Of Jim Busby Sent: Wednesday, November 08, 2006 1:31 PM To: <st1:PersonName w:st="on">College and University Technicians</st1:PersonName> Subject: Re: [CAUT] gorilla glue<o:p></o:p> </div> <o:p> </o:p> Thanks Dale. Of course, I was hoping you’d have some magic solvent or voodoo for me. What an awful glue…<o:p></o:p> <o:p> </o:p> Jim Busby BYU<o:p></o:p> <o:p> </o:p> <div> <div class=MsoNormal align=center style='text-align:center'> <hr size=2 width="100%" align=center tabindex=-1> </div> From: caut-bounces@ptg.org [mailto:caut-bounces@ptg.org] On Behalf Of Ward & Probst, Inc Sent: Wednesday, November 08, 2006 10:15 AM To: '<st1:PersonName w:st="on">College and University Technicians</st1:PersonName>' Subject: Re: [CAUT] gorilla glue<o:p></o:p> </div> <o:p> </o:p> <div> Jim,<o:p></o:p> </div> <div>  <o:p></o:p> </div> <div> I think you'll have to cut the hammers off to save the shanks. I'd use a band saw to remove as much as possible. then whittle off the rest. I am pretty sure that poly glue is not susceptible to solvents after it sets. All that said, you'd have enough time in the job to have to weigh it against the cost of new parts, particularly if the original parts need repining, etc. I'd guess it'd would take two to three hours to clean up the old shanks. Unless they are unusual or costly shanks, that would be at least half the way to new parts.<o:p></o:p> </div> <div>  <o:p></o:p> </div> <div> Good luck,<o:p></o:p> </div> <div> Dale<o:p></o:p> </div> <div> Dale E. Probst, RPT<o:p></o:p> Ward & Probst, Inc.<o:p></o:p> <st1:place w:st="on"><st1:City w:st="on">Wichita Falls</st1:City>, <st1:State w:st="on">TX</st1:State></st1:place> <o:p></o:p> <a href="mailto:dale@wardprobst.com">mailto:dale@wardprobst.com</a><o:p></o:p> <a href="http://www.wardprobst.com/">www.wardprobst.com</a><o:p></o:p> <o:p> </o:p> </div> <blockquote style='margin-top:5.0pt;margin-right:0in;margin-bottom:5.0pt'> -----Original Message----- From: caut-bounces@ptg.org [mailto:caut-bounces@ptg.org] On Behalf Of Jim Busby Sent: Wednesday, November 08, 2006 10:36 AM To: <st1:PersonName w:st="on">College and University Technicians</st1:PersonName> Subject: [CAUT] gorilla glue<o:p></o:p> List,<o:p></o:p> <o:p> </o:p> All the talk of glue brings me to this problem/question. Someone used gorilla glue to hang some hammers that I want to remove and I can’t find ANYTHING that will work. I know I could simply buy new shanks and flanges, but does anyone know of anything that’s works on this stuff??<o:p></o:p> <o:p> </o:p> Thanks.<o:p></o:p> <o:p> </o:p> Jim Busby BYU<o:p></o:p> </blockquote> </div> </body> </html>