<html xmlns:o="urn:schemas-microsoft-com:office:office" xmlns:w="urn:schemas-microsoft-com:office:word" xmlns:st1="urn:schemas-microsoft-com:office:smarttags" xmlns="http://www.w3.org/TR/REC-html40">
<head>
<meta http-equiv=Content-Type content="text/html; charset=us-ascii">
<meta name=Generator content="Microsoft Word 11 (filtered medium)">
<o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags"
name="PersonName"/>
<!--[if !mso]>
<style>
st1\:*{behavior:url(#default#ieooui) }
</style>
<![endif]-->
<style>
<!--
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
        {margin:0in;
        margin-bottom:.0001pt;
        font-size:12.0pt;
        font-family:"Times New Roman";}
a:link, span.MsoHyperlink
        {color:blue;
        text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
        {color:purple;
        text-decoration:underline;}
span.EmailStyle17
        {mso-style-type:personal-compose;
        font-family:Arial;
        color:windowtext;}
@page Section1
        {size:8.5in 11.0in;
        margin:1.0in 1.25in 1.0in 1.25in;}
div.Section1
        {page:Section1;}
-->
</style>
</head>
<body lang=EN-US link=blue vlink=purple>
<div class=Section1>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'>List,<o:p></o:p></span></font></p>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'><o:p> </o:p></span></font></p>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'>When you adjust the springs (for grams) in the Renner
underlever system how/where do you take the measurement? I’ve installed
about a dozen of these and realized maybe I haven’t been doing it
correctly. Here’s the dilemma;<o:p></o:p></span></font></p>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'><o:p> </o:p></span></font></p>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'>Of course the spring increases resistance as you go upwards.
When you measure the # 1 lever as it’s parallel to the keybed the grams
read 30. Lower it slightly below (10 degrees?) parallel and it reads 26. Raise
it slightly above level and it’s 33. Renner asks for 29 low – 32 high.
Is there a “best” way to do this or have I been OK to just do them
all at the same place, i.e. parallel, or level to the keybed?<o:p></o:p></span></font></p>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'><o:p> </o:p></span></font></p>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'>Thanks,<o:p></o:p></span></font></p>
<p class=MsoNormal><st1:PersonName w:st="on"><font size=2 face=Arial><span
style='font-size:10.0pt;font-family:Arial'>Jim Busby</span></font></st1:PersonName><font
size=2 face=Arial><span style='font-size:10.0pt;font-family:Arial'> BYU<o:p></o:p></span></font></p>
</div>
</body>
</html>