<html><body style="word-wrap: break-word; -webkit-nbsp-mode: space; -webkit-line-break: after-white-space; ">
The belt sander I use runs at 1725 RPM, 3000SFPM. With any care at all and a glass of water (only needed sometimes) heat is not a problem.<div><br></div><div>Tim G</div><div><br><div><div>On Aug 5, 2008, at 9:33 AM, Paul T Williams wrote:</div><br class="Apple-interchange-newline"><blockquote type="cite"><br><font size="2" face="sans-serif">What RPM does it run at?</font> <br> <br><font size="2" face="sans-serif">PW</font> <br> <br> <br> <br> <table width="100%"> <tbody><tr valign="top"> <td width="40%"><font size="1" face="sans-serif"><b>Tim Geinert <<a href="mailto:geinert@drtel.net">geinert@drtel.net</a>></b> </font> <br><font size="1" face="sans-serif">Sent by: <a href="mailto:caut-bounces@ptg.org">caut-bounces@ptg.org</a></font><p><font size="1" face="sans-serif">08/05/2008 09:25 AM</font> <table border=""> <tbody><tr valign="top"> <td bgcolor="white"> <div align="center"><font size="1" face="sans-serif">Please respond to<br> College and University Technicians <<a href="mailto:caut@ptg.org">caut@ptg.org</a>></font></div></td></tr></tbody></table> <br> </p></td><td width="59%"> <table width="100%"> <tbody><tr valign="top"> <td> <div align="right"><font size="1" face="sans-serif">To</font></div> </td><td><font size="1" face="sans-serif">College and University Technicians <<a href="mailto:caut@ptg.org">caut@ptg.org</a>></font> </td></tr><tr valign="top"> <td> <div align="right"><font size="1" face="sans-serif">cc</font></div> </td><td> </td></tr><tr valign="top"> <td> <div align="right"><font size="1" face="sans-serif">Subject</font></div> </td><td><font size="1" face="sans-serif">Re: [CAUT] Work Sharp</font></td></tr></tbody></table> <br> <table> <tbody><tr valign="top"> <td> </td><td></td></tr></tbody></table> <br></td></tr></tbody></table> <br> <br> <br><font size="3">Paul, List</font> <br> <br><font size="3">You might also wish to look at the Surgi-Sharp system sold by Wapin Company. </font> <br><a href="http://www.wapin.com/SurgiSharp_1.htm"><font size="3" color="blue"><u>http://www.wapin.com/SurgiSharp_1.htm</u></font></a> <br><font size="3">It is for a 1x30 or 1x42 benchtop sander that is common and usefull, is extremely versitile(knives and such are easy) and sells for only $60 with shipping.</font> <br> <br><font size="3">Tim G</font> <br> <br><font size="3">On Aug 5, 2008, at 8:33 AM, Paul T Williams wrote:</font> <br> <br><font size="2" face="sans-serif"><br> Hi List,</font><font size="3"> <br> </font><font size="2" face="sans-serif"><br> I just found out about a great tool sharpening tool at </font><a href="http://www.worksharptools.com/"><font size="2" color="blue" face="sans-serif"><u>www.worksharptools.com</u></font></a><font size="2" face="sans-serif"> Check it out! It would save hours sharpening chisels, etc. and not too spendy.</font><font size="3"> <br> </font><font size="2" face="sans-serif"><br> Paul</font><font size="3"> <br> </font> <br> <br></blockquote></div><br></div></body></html>