<HTML>
<HEAD>
<TITLE>Re: [CAUT] existing pins</TITLE>
</HEAD>
<BODY>
<FONT FACE="Calibri, Verdana, Helvetica, Arial"><SPAN STYLE='font-size:11pt'>Hi y’all,<BR>
<BR>
Thanks for the input. I think we’ve decided to just go ahead and replace the pins with lo-torque. We seldom would have need for a hoist or the room to keep one of those portable things from Harbor Freight. But that’s why I put the idea out there for all to share.<BR>
<BR>
<BR>
Jeff Farris<BR>
Piano Technician<BR>
School of Music<BR>
UT Austin<BR>
<a href="jfarris@mail.utexas.edu">jfarris@mail.utexas.edu</a><BR>
512-471-0158<BR>
<BR>
<BR>
On 8/14/08 4:26 PM, "Ward & Probst, Inc" <<a href="wardprobst@wardprobst.com">wardprobst@wardprobst.com</a>> wrote:<BR>
<BR>
</SPAN></FONT><BLOCKQUOTE><SPAN STYLE='font-size:11pt'><FONT COLOR="#0000FF"><FONT FACE="Arial">Hi Jeff,<BR>
</FONT></FONT><FONT FACE="Calibri, Verdana, Helvetica, Arial"> <BR>
</FONT><FONT COLOR="#0000FF"><FONT FACE="Arial">I've used a shop crane for pulling plates quite a few times. An example is here: <a href="http://ww2.harborfreight.com/cpi/ctaf/Displayitem.taf?itemnumber=93840">http://ww2.harborfreight.com/cpi/ctaf/Displayitem.taf?itemnumber=93840</a><BR>
It folds up pretty compactly for storage.<BR>
DP<BR>
</FONT></FONT><FONT FACE="Arial">Dale Probst, RPT<BR>
Midwestern State University<BR>
</FONT></SPAN><BLOCKQUOTE><SPAN STYLE='font-size:11pt'><FONT FACE="Calibri, Verdana, Helvetica, Arial"> <BR>
<BR>
</FONT><FONT FACE="Tahoma, Verdana, Helvetica, Arial">-----Original Message-----<BR>
<B>From:</B> <a href="caut-bounces@ptg.org">caut-bounces@ptg.org</a> [<a href="mailto:caut-bounces@ptg.org">mailto:caut-bounces@ptg.org</a>] <B>On Behalf Of </B>Jeff Farris<BR>
<B>Sent:</B> Thursday, August 14, 2008 2:19 PM<BR>
<B>To:</B> College and University Technicians<BR>
<B>Cc:</B> <a href="linnroath@mail.utexas.edu">linnroath@mail.utexas.edu</a><BR>
<B>Subject:</B> [CAUT] existing pins<BR>
<BR>
</FONT><FONT FACE="Calibri, Verdana, Helvetica, Arial">Hey list,<BR>
<BR>
One more post about restringing with existing pins. We had a lot of good points brought up last time. I like Jon Page’s beckett tool, for instance. <BR>
<BR>
This time I’m curious if anyone has pulled the plate, without a hoist, while leaving the existing tuning pins in place. We do not have means to mount anything like a wench or whatever to pull plates. We normally have our movers show up with enough manpower to simply lift them out, and set them back in place. But we’ve never attempted using the existing pins. It happens to be a “D”. I’m concerned about the angle of the pins vs. the nosebolts. And holding all that weight long enough to deal with any “problems” that pop up. Any thoughts on this? Has anyone ever done it?<BR>
<BR>
Jeff Farris<BR>
Piano Technician<BR>
School of Music<BR>
UT Austin<BR>
<a href="jfarris@mail.utexas.edu">jfarris@mail.utexas.edu</a><BR>
512-471-0158<BR>
</FONT></SPAN></BLOCKQUOTE><SPAN STYLE='font-size:11pt'><FONT FACE="Calibri, Verdana, Helvetica, Arial"><BR>
</FONT></SPAN></BLOCKQUOTE><SPAN STYLE='font-size:11pt'><FONT FACE="Calibri, Verdana, Helvetica, Arial"><BR>
<BR>
</FONT></SPAN>
</BODY>
</HTML>