<html>
<head>
<style><!--
.hmmessage P
{
margin:0px;
padding:0px
}
body.hmmessage
{
font-size: 10pt;
font-family:Tahoma
}
--></style>
</head>
<body class='hmmessage'><div dir='ltr'>
Don,<BR>
And people call ME crazy! lol.<BR>
When I was in MD (Kitts) field work on one of the ASC units. <BR>I fit my electric dremel with the router fiting. First a round (ball type) grinder then a cylindrical (like Alan pictured) <BR>
YES lots-and lots and lots of filings. I used 2 large magnets, one attached to the plate above the grinding and the other on the keybed<BR>below the grinding area in additinon to a vacumn. <BR>Don't have to repeat take your time but, hey, I just did. <BR>
Slow & steady wins the battle. Good luck!<BR>
Gerry<BR>
Gerry Cousins<BR>WCUPA<BR>
<BR>
PS Hope its billable<BR>
<BR>
<DIV>
<HR id=stopSpelling>
From: amccoy@ewu.edu<BR>To: caut@ptg.org<BR>Date: Tue, 26 Jul 2011 13:08:37 -0700<BR>Subject: Re: [CAUT] Grinding plate counter-bearing<BR><BR>
<META content="Microsoft SafeHTML" name=Generator><FONT face=Garamond><SPAN style="FONT-SIZE: 14pt">Hi Don,<BR><BR>I have never done this with the pins in. An angle die grinder with various carbide burrs will work fine to hog off the majority of the material. I use burrs with several shapes – christmas tree, cylindrical and one I find particularly useful is one like this: <IMG src="cid:3394530517_6050391"> Then, still using the die grinder switch to a 2” sanding disc. Start with 36 grit, then move up in grits. That’ll get you a decently flat surface.<BR><BR>I don’t think I’d use a Dremel for this work mostly because I just prefer using air tools. Wear a mask. The cast iron bits will go everywhere so cover everything up well, and because you are in a home (yikes!) you might use a vacuum as you work.<BR><BR>Alan McCoy<BR><BR>
<HR align=center width="95%" SIZE=3>
<B>From: </B>Don Mannino <<A href="http://dmannino@kawaius.com" target=_blank>dmannino@kawaius.com</A>><BR><B>Reply-To: </B>CAUTlist <<A href="http://caut@ptg.org" target=_blank>caut@ptg.org</A>><BR><B>Date: </B>Tue, 26 Jul 2011 09:11:01 -0700<BR><B>To: </B>CAUTlist <<A href="http://caut@ptg.org" target=_blank>caut@ptg.org</A>><BR><B>Subject: </B>[CAUT] Grinding plate counter-bearing<BR><BR></SPAN><FONT size=2><SPAN style="FONT-SIZE: 12pt">Hi all,<BR> <BR>I have a little project I need to work on, and thought I would ask for some advice. I need to grind the treble counter-bearings off of the plate of a piano in a customer’s home. I am hoping someone here has a good suggestion for which tool works best to give a clean removal that stays relatively flat. I would like to avoid screwing up the plate finish nearby, and leave a flat surface that I can put a half-round on.<BR> <BR>With the tuning pins staying in place, I’m thinking a flat grinding wheel might not fit in there. I can use a Dremel, but am worried it will be very hard to get it smooth and level.<BR> <BR>Keeping in mind the need to do it in the home, any suggestions? Dremel with a specific tip, maybe? <BR> <BR>Don Mannino RPT<BR></SPAN></FONT></FONT><FONT size=2><FONT face="Calibri, Verdana, Helvetica, Arial"><SPAN style="FONT-SIZE: 11pt"><BR></SPAN></FONT></FONT><FONT face=Garamond><SPAN style="FONT-SIZE: 14pt"><BR></SPAN></FONT></DIV>                                            </div></body>
</html>