<font color='navy' size='2' face='Comic Sans MS, sans-serif'><font color="#000080" face="Comic Sans MS, sans-serif" size="2">Hi&nbsp;</font><font color="#000080" face="Comic Sans MS, sans-serif">Robert</font>
<div style="color: navy; font-family: 'Comic Sans MS', sans-serif; font-size: 10pt; ">&nbsp;Is this is a school piano?</div>

<div><font color="#000080" face="Comic Sans MS, sans-serif" size="2">&nbsp;The length and wire size need to be measured and run thru a scaling program to see what the tension is. The Model B stwy has the same issues of low tension with the tension dropping off from approx 155 lbs per string to around 110 lbs at the break. I have corrected the tonal issues in several ways. Either by adding a few wrapped bicords on the&nbsp;</font><font color="#000080" face="Comic Sans MS, sans-serif">existing</font><font color="#000080" face="Comic Sans MS, sans-serif" size="2">&nbsp;bridge, which I would suggest here.. or adding a transition bridge with wrapped strings. Either way was an improvement. Its doubtful going up a size will improve enough &nbsp;and could likely create other tonal problems. Just my two cents worth</font>
<div style="color: navy; font-family: 'Comic Sans MS', sans-serif; font-size: 10pt; ">&nbsp; Dale<br>
<br>

<div style="clear:both"><font size="1" color="royalblue"><b><font face="Georgia, Times New Roman, Times, Serif"><font color="black"><font color="mediumblue" face="Comic Sans MS, sans-serif">Dale Erwin R.P.T.<br>
<font color="green">Erwin's Piano Restoration Inc.</font><br>
</font></font></font></b></font><font color="darkgreen"><span style="font-style: italic;"><b><font size="1"><font size="1" color="black"><font color="blueviolet"><font color="black"> <font color="black" face="Comic Sans MS, sans-serif">Mason &amp; Hamlin</font><font face="Comic Sans MS, sans-serif">/Steinway/</font><font color="black" face="Comic Sans MS, sans-serif">U.S. pianos</font><font face="Comic Sans MS, sans-serif"><br>
</font></font></font></font><font size="1" color="cornflowerblue" face="Comic Sans MS, sans-serif">www.Erwinspiano.com</font><font size="1"><br>
</font><font size="1" color="crimson" face="Comic Sans MS, sans-serif">Phone: 209-577-8397</font><br>
<font color="darkgreen"></font></font></b></span></font><tt><tt><font color="darkgreen"><br>
&nbsp;</font><br>
&nbsp; <font size="2"></font></tt></tt><br>
<br>
</div>
<br>
<br>

<div style="font-family:arial,helvetica;font-size:10pt;color:black">-----Original Message-----<br>
From: Robert Callaghan &lt;robert.callaghan@harmonicity.com&gt;<br>
To: caut &lt;caut@ptg.org&gt;<br>
Sent: Mon, Aug 27, 2012 7:12 am<br>
Subject: [CAUT] partial rescaling of C7<br>
<br>







<div id="AOLMsgPart_0_bcb3238d-4aca-4571-a69c-0ef9436ed130" style="margin: 0px;font-family: Tahoma, Verdana, Arial, Sans-Serif;font-size: 12px;color: #000;background-color: #fff;">

<pre style="font-size: 9pt;"><tt>Hello.  What are your thoughts on changing to a heavier gauge wire on 
the two lowest tenor notes just above the break on a C7?  People have 
told me they want more tone from them, and what it sounds like to me is 
the wire gauge is just a little too light.  Perhaps they should have 
even been wound strings there.  It's a fine piano and I wouldn't be 
critical of it myself, but I'm being pressured to see if there is 
anything that can be done to make that F and F# more resonant.  It's 
from 1977 and I wonder if maybe Yamaha themselves have made some slight 
changes in that area to the C7 over the years.

Thank you for any suggestions.
Robert

</tt></pre>
</div>
 <!-- end of AOLMsgPart_0_bcb3238d-4aca-4571-a69c-0ef9436ed130 -->



</div>
</div>
</div>
</font>