<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; =
charset=US-ASCII">
<META content="MSHTML 6.00.2800.1226" name=GENERATOR></HEAD>
<BODY id=role_body style="FONT-SIZE: 10pt; COLOR: #000000; =
FONT-FAMILY: Arial"
bottomMargin=7 leftMargin=7 topMargin=7 rightMargin=7>
<DIV><SPAN class=906413715-08112004><FONT face="Comic Sans MS" =
color=#000080
size=3>Mary, didn't you get a copy of my handout down in Texas a =
couple of years
back? The drawing showed the slight modification to the rail and the
step-by-step process was included on the same page.</FONT></SPAN></DIV>
<DIV><SPAN class=906413715-08112004><FONT face="Comic Sans MS" =
color=#000080
size=3></FONT></SPAN> </DIV>
<DIV><SPAN class=906413715-08112004><FONT face="Comic Sans MS" =
color=#000080
size=3>Del</FONT></SPAN></DIV>
<BLOCKQUOTE dir=ltr
style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000080 2px =
solid; MARGIN-RIGHT: 0px">
<DIV class=OutlookMessageHeader dir=ltr align=left><FONT =
face=Tahoma
size=2>-----Original Message-----<BR><B>From:</B> =
caut-bounces@ptg.org
[mailto:caut-bounces@ptg.org]<B>On Behalf Of
</B>Erwinspiano@aol.com<BR><B>Sent:</B> November 08, 2004 7:02
AM<BR><B>To:</B> caut@ptg.org<BR><B>Subject:</B> Re: [CAUT] Re: =
Steinway
Damper sytem upgrade & redesign<BR><BR></FONT></DIV><FONT =
id=role_document
face=Arial color=#000000 size=2>
<DIV>
<DIV>In a message dated 11/8/2004 6:47:46 AM Pacific Standard Time,
marysmith@mail.utexas.edu writes:</DIV>
<BLOCKQUOTE
style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: blue 2px =
solid"><FONT
style="BACKGROUND-COLOR: transparent" face=Arial color=#000000 =
size=2>Dale,<BR><BR>Though I missed your "dreaded" OT posts (oops, =
must have
hit that delete key too soon!), I'm glad I took a moment to read =
this
message about damper systems. Excellent advice. The capstan =
installation
under each underlever is new to me. How long would you say this =
takes? It
sounds like a super upgrade - I hate feeling inadequate because I =
can't
regulate milli-micron amounts of change under the pinblock without =
looking
by turning those dadburned screws, etc, etc... Thanks for putting =
all those
ideas together in one =
place!<BR><BR>Mary<BR></FONT></BLOCKQUOTE></DIV>
<DIV></DIV>
<DIV> Mary</DIV>
<DIV> I was surprised that it took relatively little time. =
Remember I
did make one pass on the table saw for a relief cut Took
5 minutes.Marking & drilling holes about 30 minutes. Tapping =
in was
about 30 minutes. Cost of parts was nominal.</DIV>
<DIV> Oh come on, Are you sure you don't need another OT?</DIV>
<DIV> Dale</DIV>
<DIV> </DIV></BLOCKQUOTE></FONT></BODY></HTML>