<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; =
charset=us-ascii">
<META content="MSHTML 6.00.2800.1126" name=GENERATOR></HEAD>
<BODY>
<DIV>
<P><SPAN class=801183621-14022003><FONT size=2>The measurements I =
have are
:</FONT></SPAN></P>
<P><FONT size=2>Wippen Height: 3-1/4 inches (82.55 mm)</FONT></P>
<P><FONT size=2>Hammer<SPAN class=801183621-14022003> </SPAN>shank =
Height: 5-3/4
inches (146.05 mm)</FONT></P>
<P><FONT size=2>Spread: 4-13/32 inches (111.9 mm)</FONT></P></DIV>
<DIV><SPAN class=801183621-14022003><FONT face=Arial color=#0000ff =
size=2>Strings heights are supposed to be 192 mm & 200
mm</FONT></SPAN></DIV>
<DIV><SPAN class=801183621-14022003><FONT face=Arial color=#0000ff =
size=2></FONT></SPAN> </DIV>
<DIV><SPAN class=801183621-14022003><FONT face=Arial color=#0000ff =
size=2>These
are actual measures</FONT></SPAN></DIV>
<DIV><SPAN class=801183621-14022003><FONT face=Arial color=#0000ff =
size=2></FONT></SPAN> </DIV>
<DIV><SPAN class=801183621-14022003><FONT face=Arial color=#0000ff =
size=2>Hope
it helps</FONT></SPAN></DIV>
<DIV><SPAN class=801183621-14022003><FONT face=Arial color=#0000ff =
size=2></FONT></SPAN> </DIV>
<DIV><SPAN class=801183621-14022003><FONT face=Arial color=#0000ff =
size=2>Regards</FONT></SPAN></DIV>
<P><FONT size=2>Isaac OLEG<BR><BR>Entretien et réparation de
pianos.<BR><BR>PianoTech<BR>17 rue de Choisy<BR>94400 VITRY sur
SEINE<BR>FRANCE<BR>tel : 033 01 47 18 06 98<BR>fax : 033 01 47 18 06 =
90<BR>cell:
06 60 42 58 77 </FONT></P>
<BLOCKQUOTE
style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #0000ff 2px =
solid">
<DIV class=OutlookMessageHeader dir=ltr align=left><FONT =
face=Tahoma
size=2>-----Message d'origine-----<BR><B>De :</B> =
caut-bounces@ptg.org
[mailto:caut-bounces@ptg.org]<B>De la part de</B>
Wimblees@aol.com<BR><B>Envoyé :</B> vendredi 14 =
février 2003
01:05<BR><B>À :</B> Pianotech@PTG.org;
caut@ptg.org<BR><B>Objet :</B> help with action
geometry<BR><BR></FONT></DIV><FONT face=arial,helvetica><FONT =
lang=0
face=Arial size=2 FAMILY="SANSSERIF">I am in the process of =
rebuilding a 1895
Model A, which was done once before, but very poorly. The first thing =
I
noticed, and the thing the customer complained about, was an extremely =
heavy
action. This was because there was a lot of let off, about 1/2". When =
I
removed the fall board, I noticed that the pin block (which had been
replaced), was sticking down from the front stretcher about =
1/4". My
first inclination was that the plate was set back in the piano too =
high, and
that is why there was so much let off. <BR><BR>I have replaced =
the pin
block, and the plate is back in the right position, and there is good
downbearing. But I am now starting to work on the action, replacing =
the h/s/f
and wips. Now I see why there was so much let off. This other =
rebuilder used a
1 1/2" thick pin block. But instead of planing down the entire block, =
he only
trimmed down the ends, which rest on the inner rim, but he left rest =
of the
pin block the original 1 1/2". That is why there is about a 1/4" of =
pin block
sticking down below the stretcher. Obviously that wouldn't allow the =
action to
slide in. So in order to get the action in, he lowered the action by =
shaving
down the action frame mounting blocks. (I think that is what they are =
called).
<BR><BR>I want to replace the blocks. But the question I have is =
measurements.
About 20 years ago when I put a new action in a Steinway, and these =
blocks
were not attached to the action frame. I think I remember I had to =
sort of go
by where the striking point was of the last couple of notes, combined =
with the
hieght of the hammers. I had a hell of time figuring out where to put =
them. Is
there some measurement I can go by to determine where I have to put =
the
blocks, and how high the action has to be?<BR><BR>Wim</FONT>
</FONT></BLOCKQUOTE></BODY></HTML>