This is a multi-part message in MIME format. ---------------------- multipart/alternative attachment Dale, Thanks. I'll follow up with a phone call to Bill Spurlock. PS...this goes out to everyone who contributes to this list. I was trying to explain to her how valuable this list has become to so = many. Here I was with a dilemma and wasn't too sure how to proceed. = Normally I would experiment using some valuable time and effort and = eventually would come to my conclusion. With the list, however, one can = put out the question and within a short time answers and opinions come = from , literally, around the world. This list has transformed the way I = do business. Again, thanks to those who helped with the input. Hopefully I can return = the favors down the road. Tom Servinsky,RPT ----- Original Message -----=20 From: DALE ERWIN=20 To: pianotech=20 Sent: Sunday, October 14, 2001 11:38 PM Subject: Re: Keytop routing techniques Hi Tom Bill Spurlock has done a key recovering class for years that details = his setup which works slick and parts of it you could use to answer your = ?s. He has a fine handout I'm guessin you could request from him. Dale Erwin ----- Original Message ----- From: Tom Servinsky Sent: Sunday, October 14, 2001 6:17 PM To: pianotech@ptg.org Subject: Re: Keytop routing techniques Thanks to all for the needed information. Sounds like PVC-E is the = adhesive of choice. Ron N, thanks for the heads up with the small blade for trimming. = Tried it and it works fine. Again, thanks to all. I appreciate the input. Tom Servinsky,RPT ----- Original Message ----- From: "Thomas Cole" <tcole@cruzio.com> To: <pianotech@ptg.org> Sent: Sunday, October 14, 2001 1:57 PM Subject: Re: Keytop routing techniques > Tom, > > I let them set up overnight although it probably cures faster than = that. > Clamping is not necessary. PVC-E is definitely the way to go. > > When you trim with a laminate trimmer, you need to set the bit = just high > enough so that the bearing rides on the wood nearest the keytop = and > misses the key lead holes. > > For the inevitability that one or two keytops will become damaged = in the > trimming process, I recommend having a spare set on hand for = individual replacement. > > Tom Cole > > Tom Servinsky wrote: > > > > Dave, > > What is the set up time with PVC glue? > > Is clamping still necessary? > > Tom Servinsky,RPT > > ----- Original Message ----- > > From: "David Renaud" <drjazzca@yahoo.ca> > > To: <pianotech@ptg.org> > > Sent: Sunday, October 14, 2001 9:54 AM > > Subject: Re: Keytop routing techniques > > > > > what is the keytop cement of choice. I was > > > > introduced to using acetone and a melted plastic > > > > keytop made into a honey viscosity consistently. > > > > Within 30 seconds the bond is strong. The downside > > > > is you have to be extremely careful not to transfer > > > > any acetone anywhere near the surface of the key or > > > > the finish will be marred. Tom Servinsky,RPT > > > > > > > > > PCV-E glue. Simple, quick, strong, clean. > > > > > > I get it in Canada from Pianophile, or Bolduc. > > > > > > Dave Renaud > > > RPT > > > > > > > > > _______________________________________________________ > > > Do You Yahoo!? > > > Get your free @yahoo.ca address at http://mail.yahoo.ca ---------------------- multipart/alternative attachment An HTML attachment was scrubbed... URL: https://www.moypiano.com/ptg/pianotech.php/attachments/e4/39/92/1c/attachment.htm ---------------------- multipart/alternative attachment--
This PTG archive page provided courtesy of Moy Piano Service, LLC