Terry & - Just to let you know, the link below doesn't work because of the stray parenthesis { ) } at the end. The remaining link is correct, and scary. How many of these did you say you had? David Skolnik At 07:56 AM 1/29/2003, you wrote: >Thanks for the response David. I will post to the Shapton site - I didn't >realize they had a forum. The guy that made me several very nice wooden >planes (Steve Knight: http://www.knight-toolworks.com/wooden.htm) highly >(and I mean HIGHLY) recommended the Shapton ceramic stones. They do cut >very well, and wear very slowly. I had used an EZ lap diamond stone prior >to that and liked that plate quite a bit, but Steve just about hit the >roof when I suggested that I might sharpen his iron on a diamond plate. He >said it would ruin the iron. I don't have a clue why that would be the >case. I'll try the Shapton forum. Maybe I'll have a Zen-like experience. > >Terry Farrell > >----- Original Message ----- >From: "David Skolnik" <davidskolnik@optonline.net> >To: "Pianotech" <pianotech@ptg.org> >Sent: Wednesday, January 29, 2003 12:37 AM >Subject: Re: Plane/Chisel Stone Sharpening > > > > Terry - > > > > Like Greg Newell, I would recommend a Tormek, which I own and am happy > > with, however, I went to the Shapton site and went into the forums. I > > realized that you probably already have a considerable investment in these > > stones, and a lot of people in the Zen sharpening culture seem to think > > very highly of them. Of the discussions I read, no one seems to imply > that > > they use any guides with these stones. Why don't you post to them? They > > seem to be willing to address this sort of question, though I suspect you > > might want to retire the skill/experience comment, for obvious (I think) > > reasons. I did get the sense that these stones are designed for Japanese > > style cutting tools, not Western. Sharpening...Now, there's something > > uncontroversial. Good luck > > > > David Skolnik > > > > At 08:57 PM 1/28/2003, you wrote: > > >I have a question for those who sharpen plane blades and/or chisels on > > >some type of stone (Japanese waterstone, ceramic, Arkansas, or whatever) > > >and use a honing guide. I have trouble reproducing the EXACT angle of the > > >blade in the honing guide when I want to touch up the edge. Or if I am > > >sharpening several plane blades and chisels, I would like to do all the > > >coarse work first, then the medium grits, fine, and then polishing. (I've > > >been sharpening ALL my chisels and planes for TWO DAYS NOW.) But unless I > > >have a honing guide for each piece, I find it very difficult to reproduce > > >the exact angle for fine grinding and polishing. The only way I can > really > > >see it working is to attach the honing guide to one piece and go through > > >all necessary grits (or have a honing guide for each piece to be > > >sharpened). Then next time the blade needs some touchup, you will need to > > >go to a grit that is able to correct any angle deviation that you have > > >from mis-angling the honing guide. > > > > > >I am using Shapton ceramic sharpening > > >stones: http://www.shaptonstones.com/ (Professional Series) and the > > >Veritas Honing Guide and Bevel Setter: http://www.garrettwade.com/ (type > > >in "veritas honing guide). > > > > > >Am I missing something here? Or is this a universal problem? Or is this > > >one of those skill/experience things (damn, I hate those)? > > > > > >Terry Farrell > > > > > > > > >_______________________________________________ > > >pianotech list info: https://www.moypiano.com/resources/#archives > > > > > > _______________________________________________ > > pianotech list info: https://www.moypiano.com/resources/#archives >_______________________________________________ >pianotech list info: https://www.moypiano.com/resources/#archives
This PTG archive page provided courtesy of Moy Piano Service, LLC