TuneLab

[Alan]

This is a multi-part message in MIME format.

---------------------- multipart/alternative attachment
Fabulous, affordable. Get it, you=92ll love it. Check the archives for
more comments.
=20
Alan R. Barnard
Salem, MO
-----Original Message-----
From: pianotech-bounces@ptg.org [mailto:pianotech-bounces@ptg.org] On
Behalf Of Harry Pickett
Sent: Tuesday, June 24, 2003 9:19 AM
To: 'Pianotech'
Subject: TuneLab
=20
Hi all,
Does anyone use Tunelab? I can=92t see myself being able to afford a SAT
in the near future and would like an aid to the aural tuning I am doing
now.
Comments O wise ones!
Cheers
Harry
=20
=20
Harry Pickett
=20
-----Original Message-----
From: pianotech-bounces@ptg.org [mailto:pianotech-bounces@ptg.org] On
Behalf Of Richard Strang
Sent: Monday, June 23, 2003 8:01 PM
To: 'Pianotech'
Subject: RE: Restringing
=20
I learned how to make a pretty nice loop using  a pair of vise grips and
a screw driver. I make a loop and clamp it with the vise grips, lightly
of course, then stick the screw drive through the loop and twist 6 or 7
times. Comes out just fine for some of the clunkers I work on.
=20
Richard
-----Original Message-----
From: pianotech-bounces@ptg.org [mailto:pianotech-bounces@ptg.org]On
Behalf Of Dave Bunch
Sent: Monday, June 23, 2003 6:36 PM
To: Pianotech
Subject: Re: Restringing
As far as loop makers go, I would warn someone new to this to avoid the
loop makers with the crank commonly seen in the catalogs. They are good
for nothing but breaking wire. With just a little practice, one can make
a first rate loop by hand using nothing more than a nail in a vise. This
will work fine for the 99% of pianos that have just one or two looped
strings.
=20
Dave Bunch
----- Original Message -----=20
From: HYPERLINK "mailto:tune4u@earthlink.net"Alan=20
To: HYPERLINK "mailto:pianotech@ptg.org"'Pianotech'=20
Sent: Monday, June 23, 2003 11:28 AM
Subject: RE: Restringing
=20
Yes ...
=20
Not a complete treatise, but a few thoughts.
=20
First time, it will take you close to three 8-days.
An experienced person can do it in about two days.
I don't think it's fair for people to pay for my "learning curves," so I
would bill the job based on, say, 18 hours.
Take the job. Learn and earn.
=20
Critical things to have, purchase, or make-your-own ...
=20
1.       A pinblock jack
2.       Coil maker
3.       2=BD lb sledge hammer (for fine tuning and watch repair)
4.       Real wire cutters, not pin nippers or light duty electrical
"dikes"
5.       Heavy gloves or, better yet, glass-handler's gloves
6.       Eye
protection!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Many jobs
call for eye protection: Restringing SCREAMS for it. Wear industrial eye
protection, the kind that protects from the sides,
too!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
7.       Band-Aids (Don't make your own.)
=20
Helpful things to have ...
=20
1.       A =BD" drive variable speed electric drill with "pin removing
bit" (see archives). =BC" drill will not do, doesn't have enough torque,
especially at slower speeds and you don't want to spin the pins so fast
that you set the piano on fire or, more likely, damage the holes.
2.       New set of pin collars (depending). New hitch pin punchings,
felts, braid, etc. (depending)
3.       Tuning pin crank
4.       Loop maker
=20
Look up in the archives or read Reblitz, etc., about measuring strings,
marking where string sizes change, etc.
=20
Examine the piano carefully before you start:=20
1.       Make sure the legs are secure and nothing is wobbly. 999/1000
times this is no problem. The 1/1000th time, a disaster can ensue.
2.       Pull the lid hinge pins with the lid closed. Unless it is a
very small piano, get the owner or someone to help you lift off the lid
and put it in a safe place.
3.       Examine the pinblock and bridges very carefully. Discuss
problems with owner. NOW is the time to make any repairs.
4.       Note any problems or anticipated problems. Write them down.
Have the owner look at them with you and sign the paper acknowledging
the problems. Again 1/1000, but you don't want any arguments later. I
would take a torque wrench and measure each pin-or at least a good
sampling-as I made the first tension reduction turns of the pin to make
sure you spot any "patterns" suggesting block damage or any pin holes
that might need a little epoxy, etc. Easier to do it now than to have to
remove pins later.
=20
Have fun.=20
=20
Alan R. Barnard
Salem, MO
-----Original Message-----
From: pianotech-bounces@ptg.org [mailto:pianotech-bounces@ptg.org] On
Behalf Of Richard Strang
Sent: Monday, June 23, 2003 10:14 AM
To: pianotech (E-mail)
Subject: Restringing
=20
Hello, all,
    Piano restringing has always been a little out of my line of work,
as I do not have a shop. However, I have a good customer that is
requesting me to restring his grand on site, and I'm debating on whether
I should accept the job or not. Any advice?
=20
Richard
=20
---
Incoming mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.489 / Virus Database: 288 - Release Date: 6/10/2003
=20
---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.489 / Virus Database: 288 - Release Date: 6/10/2003

---
Incoming mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.489 / Virus Database: 288 - Release Date: 6/10/2003


---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.489 / Virus Database: 288 - Release Date: 6/10/2003
=20

---------------------- multipart/alternative attachment
An HTML attachment was scrubbed...
URL: https://www.moypiano.com/ptg/pianotech.php/attachments/3b/b9/f1/87/attachment.htm

---------------------- multipart/alternative attachment--