[pianotech] hour$ pinning

[Joe And Penny Goss]

Yes! You need special instructions, Call me.
Joe Goss RPT
Mother Goose Tools
imatunr at srvinet.com
www.mothergoosetools.com
----- Original Message ----- 
From: "David Ilvedson" <ilvey at sbcglobal.net>
To: <pianotech at ptg.org>
Sent: Tuesday, March 31, 2009 9:09 PM
Subject: Re: [pianotech] hour$ pinning


> I figure 2 hours but I'm not hurrying and often will only get a portion of
the job done before other things crop up...
> Question for Don:  I was wondering if the broaches need the rough area
roughed up over time and how one does that...or do you buy a new set... '-]
>
> David Ilvedson, RPT
> Pacifica, CA  94044
>
> ----- Original message ----------------------------------------
> From: "Don Mannino" <donmannino at ca.rr.com>
> To: pianotech at ptg.org
> Received: 3/31/2009 7:56:23 PM
> Subject: Re: [pianotech] hour$ pinning
>
>
> >Ed,
>
> >My record, when actively repinning a LOT of actions at a certain
> >manufacturer in the early 90s, was 50 minutes.  This includes removing
the
> >parts, repinning, and replacing the parts.   I had the help of a power
> >screwdriver and the pressure to finish before going out to lunch.  I
think I
> >also put off going to the bathroom until I finished to give me extra
> >motivation.  :-)
>
> >I think your 90 minutes is a more reasonable good time to do the job,
> >though.  I used to estimate that part of an action job for 2 hours, to
allow
> >for problems.
>
> >Don Mannino
>
> >----- Original Message ----- 
> >From: <A440A at aol.com>
> >To: <pianotech at ptg.org>
> >Sent: Tuesday, March 31, 2009 5:56 PM
> >Subject: [pianotech] hour$ pinning
>
>
> >> Greetings,
> >>   While we are talking about Barbara's pins, I wonder how much time it
> >> takes
> >> for us to repin a hammerline.  I got pretty fast at it, and Don
Maninno's
> >> pinning class certainly validated and improved some of my procedures,
etc.
> >> For
> >> most important regulation work,  I now include repinning the hammerline
as
> >> standard procedure.  If I have to pin all of them, and there is no
repairs
> >> to be
> >> done, like regluing splits or rebushing flanges,  it takes me about 90
> >> minutes.  I bet there are younger, faster, techs around, so how much
time
> >> does it
> >> take others?
> >>
> >> (I use a duplicator jig to remember where the string cuts line up
before
> >> removing all the hammerflanges, (sorta like Steve Jellen's jig of many
> >> years ago).
> >> I can then correct traveling as I reinstall them without losing my
hammer
> >> spacing.)
> >> regards,
> >> Ed Foote RPT
> >> http://www.uk-piano.org/edfoote/index.html
> >> www.uk-piano.org/edfoote/well_tempered_piano.html
> >> <BR><BR><BR>**************<BR>A Good Credit Score is 700 or Above.
> >See
> >> yours
> >> in just 2 easy steps!
> >>
>
>(http://pr.atwola.com/promoclk/100126575x1220439616x1201372437/aol?redir=ht
> >tp:%2F%2Fwww.freecreditreport.com%2Fpm%2Fdefault.aspx%3Fsc%
> >> 3D668072%26hmpgID%3D62%26bcd%3DfebemailfooterNO62)</HTML>
> >>
> >>
>
>