<html>
<body>
Another use I discovered for it was to install a new set of knuckles
using it basically <br>
the same as for hammers. Mainly to just make sure the wood core is
straight up and down <br>
coming out of the hammer shank. Worked great. <br><br>
Avery <br><br>
At 01:11 AM 7/4/05, you wrote:<br>
<blockquote type=cite class=cite cite="">
<font face="Comic Sans MS" color="#000080">It does both but, if memory
serves, it was introduced at a class on hammer hanging.<br>
</font> <br>
<font face="Comic Sans MS" color="#000080">Del<br>
</font><br>
<dl><hr>
<dd><font face="Tahoma" size=2>From:</b> pianotech-bounces@ptg.org
[<a href="mailto:pianotech-bounces@ptg.org" eudora="autourl">
mailto:pianotech-bounces@ptg.org</a>] On Behalf Of </b>David Skolnik<br>
<dd>Sent:</b> July 03, 2005 10:53 PM<br>
<dd>To:</b> Pianotech<br>
<dd>Subject:</b> RE: Baldwin Gauge?<br>
</font><br>
<dd>Gentles -<br><br>
<dd>All due respect, take another look at the photo. In fact, this
one is not the one they made to check shank to molding dimension.
Rather this was designed to check the molding / string angle with
the hammer pulled up to contact string. The folded-over part of the
shorter length would sit on top of the string (Baldwin name would be
upside down), and the longer length would be brought adjacent to the side
of the subject hammer (which would have previously had a line drawn
bisecting the molding). The gauge would indicate whether the hammer
is striking at 90 degrees or not. <br><br>
<dd>Del - you must be too busy unpacking. What an unenviable
task!<br><br>
<dd>Best to all. Remember to use your ear plugs if you end up at
the fireworks!<br><br>
<dd>David Skolnik<br><br>
<br><br>
<br>
<dd>
<a href="file://c:\docume~1\david\applic~1\qualcomm\eudora\attach\july%203.05%20036%20(2).jpg" eudora="attachment">
<img src="cid:6.2.3.4.2.20050704065941.03f9b520@pop-server.houston.rr.com.1" width=640 height=480 alt="[]">
</a>
<a href="file://c:\docume~1\david\applic~1\qualcomm\eudora\attach\july%203.05%20036%20(2).jpg" eudora="attachment">
<br>
<dd>july 3.05 036 (2).jpg </a><br><br>
<br><br>
<br><br>
<br><br>
<br><br>
<br>
<dd>At 09:21 PM 7/3/2005 -0700, you wrote:<br>
<blockquote type=cite class=cite cite="">
<dd><font face="Comic Sans MS" color="#000080">It is a convention
give-away tool used to determine whether or not a hammerhead is square to
the hammershank. Simply lay the short, bent over part on top of the
hammershank, move it so that the long, narrow part runs along the
hammerhead molding and see that the hammerhead is square to the shank.
<br>
</font>
<dd> <br>
<dd><font face="Comic Sans MS" color="#000080">When replacing hammers it
is used to draw a line along the centerline of the original hammerhead
molding on the sample hammerheads (those left in place to align the new
hammerheads to). This can be quite helpful if the original hammerheads
have been badly mis-shaped over the years.<br>
</font>
<dd> <br>
<dd><font face="Comic Sans MS" color="#000080">Del<br>
</font>
<dd> <br>
<dd> <br><br><hr>
<dl>
<dd><font face="tahoma" size=2>From: pianotech-bounces@ptg.org [
<a href="mailto:pianotech-bounces@ptg.org" eudora="autourl">
mailto:pianotech-bounces@ptg.org</a>] On Behalf Of Jack Houweling
<dd>Sent: July 03, 2005 9:04 PM
<dd>To: pianotech
<dd>Subject: Baldwin Gauge?</font>
<dd><font face="arial" size=2>Hello,
<dd>I found this in one of my tool boxes and would like to know what it
is? It is aluminum, has Baldwin written on it and is about three inches
long. Looks like some sort of gauge but I'm not sure.</font>
<dd>
<dd><font face="arial" size=2>Thanks,
<dd>Jack Houweling</font><hr>
<dd>No virus found in this incoming message.
<dd>Checked by AVG Anti-Virus.
<dd>Version: 7.0.323 / Virus Database: 267.8.8/37 - Release Date:
7/1/2005</blockquote>
</dl><br>
</dl><br>
</blockquote></body>
</html>