<html>
<head>
<META HTTP-EQUIV="Content-Type" CONTENT="text/html; =
charset=us-ascii">
<meta name=Generator content="Microsoft Word 10 (filtered)">
<style>
<!--
/* Font Definitions */
@font-face
{font-family:Tahoma;
panose-1:2 11 6 4 3 5 4 4 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:12.0pt;
font-family:"Times New Roman";}
a:link, span.MsoHyperlink
{color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{color:purple;
text-decoration:underline;}
span.EmailStyle17
{font-family:Arial;
color:navy;}
@page Section1
{size:8.5in 11.0in;
margin:1.0in 1.0in 1.0in 1.0in;}
div.Section1
{page:Section1;}
-->
</style>
</head>
<body lang=EN-US link=blue vlink=purple>
<div class=Section1>
<p class=MsoNormal><font size=2 color=navy face=Arial =
FAMILY=SANSSERIF><span
style='font-size:10.0pt;font-family:Arial;color:navy'>Charles:</span></=
font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:navy'> =
You
shouldn’t have a problem with this. The supports are =
U-shaped at
the ends, and you just need to loosen the screws. It will pull off =
the
ends of the supports. Your hardest task is snaking it out of the
action. Perhaps you’ll have to remove the action, =
though. </span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:navy'> =
Best,</span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:navy'> =
Paul
McCloud</span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:navy'> =
San
Diego</span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:navy'> </span></font></p>
<p class=MsoNormal style='margin-left:.5in'><font size=2 =
face=Tahoma><span
style='font-size:10.0pt;font-family:Tahoma'>-----Original =
Message-----<br>
<b><span style='font-weight:bold'>From:</span></b> =
pianotech-bounces@ptg.org
[mailto:pianotech-bounces@ptg.org] <b><span =
style='font-weight:bold'>On Behalf
Of </span></b>Piannerman@aol.com<br>
<b><span style='font-weight:bold'>Sent:</span></b> Sunday, October 26, =
2003
8:01 PM<br>
<b><span style='font-weight:bold'>To:</span></b> pianotech@ptg.org<br>
<b><span style='font-weight:bold'>Subject:</span></b> Haven't run into =
this
before</span></font></p>
<p class=MsoNormal style='margin-left:.5in'><font size=3 =
face="Times New Roman"><span
style='font-size:12.0pt'> </span></font></p>
<p class=MsoNormal style='margin-left:.5in'><font size=2 =
face=Arial><span
style='font-size:10.0pt;font-family:Arial'>People,<br>
I need to remove the jackstop rail from a =
Knight
piano. The piano is in a town some miles from here so I don't have =
ready
access to it. Can anyone tell me the proper way to get the sucker =
out of
there so I will be prepared when I get there? <br>
<br>
I was only able to see the flathead very thin
adjusting screws. The rail is in two sections, bass bridge section =
and
then everything else section. I am guessing I will have to unscrew =
the
adjusting screws until the rail falls off, which will take probably till
Christmas. Is there an easier or better way? Much obliged if =
anyone
can help.<br>
<br>
Charles Cron</span></font></p>
</div>
</body>
</html>