<html xmlns:o="urn:schemas-microsoft-com:office:office" xmlns:w="urn:schemas-microsoft-com:office:word" xmlns:st1="urn:schemas-microsoft-com:office:smarttags" xmlns="http://www.w3.org/TR/REC-html40">
<head>
<meta http-equiv=Content-Type content="text/html; charset=us-ascii">
<meta name=Generator content="Microsoft Word 11 (filtered medium)">
<o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags"
name="country-region"/>
<o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags"
name="State"/>
<o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags"
name="City"/>
<o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags"
name="place"/>
<!--[if !mso]>
<style>
st1\:*{behavior:url(#default#ieooui) }
</style>
<![endif]-->
<style>
<!--
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:12.0pt;
font-family:"Times New Roman";}
a:link, span.MsoHyperlink
{color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{color:purple;
text-decoration:underline;}
span.EmailStyle17
{mso-style-type:personal-compose;
font-family:Arial;
color:windowtext;}
@page Section1
{size:8.5in 11.0in;
margin:1.0in 1.25in 1.0in 1.25in;}
div.Section1
{page:Section1;}
-->
</style>
</head>
<body lang=EN-US link=blue vlink=purple>
<div class=Section1>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'>Hello list,<o:p></o:p></span></font></p>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'> <o:p></o:p></span></font></p>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'>I have a question regarding a procedure for removing a
Hardman pin block. I have replaced blocks before, but this one appears to have
been installed using a slightly different technique. While being doweled and
glued to the inner rim shelf, there is also a mortise or rabbet under the
stretcher that the pin block material is let into. The veneer on the front of
the stretcher at each end, leads me to suspect that the block / stretcher were
originally installed as a unit. Not really wanting to remove the stretcher,
I’m wondering if I could simply cut the block out in the normal fashion
(router and big bit), leaving the part of the old block that is under the
stretcher intact and gluing the new block to that. This is complicated by the
presence of a large cove cut in the bottom of the block / stretcher for
fallboard clearance. I’m hoping that some one has done this before,
and can offer a procedure that has worked in the past.<o:p></o:p></span></font></p>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'><o:p> </o:p></span></font></p>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'>Thanks for any help at all,<o:p></o:p></span></font></p>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'><o:p> </o:p></span></font></p>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'>Owen (<st1:place w:st="on"><st1:City w:st="on">Kingston</st1:City>,
<st1:State w:st="on">Ontario</st1:State>, <st1:country-region w:st="on">Canada</st1:country-region></st1:place>)<o:p></o:p></span></font></p>
<p class=MsoNormal><font size=2 face=Arial><span style='font-size:10.0pt;
font-family:Arial'><o:p> </o:p></span></font></p>
</div>
</body>
</html>