<html xmlns:v="urn:schemas-microsoft-com:vml" xmlns:o="urn:schemas-microsoft-com:office:office" xmlns:w="urn:schemas-microsoft-com:office:word" xmlns:st1="urn:schemas-microsoft-com:office:smarttags" xmlns="http://www.w3.org/TR/REC-html40"> <head> <meta http-equiv=Content-Type content="text/html; charset=us-ascii"> <meta name=Generator content="Microsoft Word 11 (filtered medium)"> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="PostalCode"/> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="State"/> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="place"/> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="City"/>  <style>  </style> </head> <body lang=EN-US link=blue vlink="#000000"> <div class=Section1> Dean,<o:p></o:p> <o:p> </o:p> Thanks for the post and I like your willingness to do what ever you can to give people a piano.<o:p></o:p> <o:p> </o:p> William<o:p></o:p> <o:p> </o:p> <div> PIANO BOUTIQUE<o:p></o:p> William Benjamin<o:p></o:p> Piano Tuner Extraordinaire<o:p></o:p> <a href="http://www.pianoboutique.biz">www.pianoboutique.biz</a><o:p></o:p> The tuner alone,<o:p></o:p> preserves the tone.<o:p></o:p>  <o:p></o:p> </div> <div> <div class=MsoNormal align=center style='text-align:center'> <hr size=2 width="100%" align=center tabindex=-1> </div> From: pianotech-bounces@ptg.org [mailto:pianotech-bounces@ptg.org] On Behalf Of Dean May Sent: Thursday, January 04, 2007 9:19 AM To: 'Pianotech List' Subject: RE: Gluing felt to moldings<o:p></o:p> </div> <o:p> </o:p> William, <o:p></o:p> <o:p> </o:p> Here is an account I posted a couple of years ago of a quick and dirty field repair.<o:p></o:p> <o:p> </o:p> I was working on a pso spinet yesterday with multiple problems for a family with a limited budget. One hammer had lost the felt and about ten others had come apart on one side. I used Goop, needle nose vice grips and dental floss. I pulled the loose felts the rest of the way off to get a good coating of glue. I held the glued felt in place with the needle nose vice grips, clamping the ends of the felt from the shank end of the molding. This left the head of the hammer open so I could wrap the dental floss around it.<o:p></o:p> I pulled out about 20 inches of dental loss and tied a loop in one end to form a lasso, leaving a good 3-4 inches of the short end of the floss sticking out of the loop's knot. This gave me something to tie off against later. The beauty of doing the lasso is that it gives you the first loop around the felt without a knot, and it is self tightening. After pulling the first loop down tight, it stayed tight while I wrapped 4 more loops around the felt. Then I tied it off and went to the next hammer.<o:p></o:p> <o:p> </o:p> Worried about the remaining hammers, I soaked CA glue into the tail end of the felt on top and bottom. It will be interesting to see if it holds.<o:p></o:p> <o:p> </o:p> One key in the treble section cracked at the dog leg. CA glue fixed it.<o:p></o:p> <o:p> </o:p> One corroded tenor string broke during tuning. I cut it off near the hitch pin and formed a loop on the unbroken leg of the wire to keep 2 strings on the note. It held.<o:p></o:p> <o:p> </o:p> Total time outside of tuning: about 45 minutes. Charges: $50.<o:p></o:p> <o:p> </o:p> Of course this is a piano that should be junked, but it is all the family can afford and it gives their girls something to practice on.<o:p></o:p> <o:p> </o:p> <div> Dean<o:p></o:p> <u1:PersonName u2:st="on">Dean May</u1:PersonName>             cell 812.239.3359 <o:p></o:p> PianoRebuilders.com   812.235.5272 <o:p></o:p> <u1:place u2:st="on"><u1:City u2:st="on"><st1:place w:st="on"><st1:City w:st="on">Terre Haute</st1:City></st1:place></u1:City> <u1:State u2:st="on"><st1:State w:st="on">IN</u1:State></st1:State>  <u1:PostalCode u2:st="on"><st1:PostalCode w:st="on">47802</u1:PostalCode></st1:PostalCode></st1:place><o:p></o:p> </div> <div> <div class=MsoNormal align=center style='text-align:center'> <hr size=2 width="100%" align=center tabindex=-1> </div> From: pianotech-bounces@ptg.org [mailto:pianotech-bounces@ptg.org] On Behalf Of William Benjamin Sent: Tuesday, January 02, 2007 12:05 PM To: Pianotech List Subject: Gluing felt to moldings<o:p></o:p> </div> <o:p> </o:p> Greetings List,<o:p></o:p> <o:p> </o:p> Do any of you have suggestions for gluing hammer felts back down to the molding?  I have a customer that can’t afford new hammers and any suggestions would be appreatiated.  Are there any clamps that would work better or any ordinary ways of doing it.  I know that they are glued under stress in the factory, and if they are just glued down, they will sound dull.  Thanks in advance for any help.<o:p></o:p> <o:p> </o:p> William<o:p></o:p> <o:p> </o:p> <o:p> </o:p> PIANO BOUTIQUE<o:p></o:p> William Benjamin<o:p></o:p> Piano Tuner Extraordinaire<o:p></o:p> <a href="http://www.pianoboutique.biz">www.pianoboutique.biz</a><o:p></o:p> The tuner alone,<o:p></o:p> preserves the tone.<o:p></o:p>  <o:p></o:p> <o:p> </o:p> </div> </body> </html>