<HTML style="FONT-SIZE: x-small; FONT-FAMILY: MS Sans Serif"><HEAD>
<META http-equiv=Content-Type content="text/html; charset=utf-8">
<META content="MSHTML 6.00.2900.3086" name=GENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY bgColor=#ffffff>
<DIV>
<DIV>Hi, Jim:</DIV>
<DIV>&nbsp;&nbsp;&nbsp;&nbsp;There are shims in the outer bracket support "feet" that are removable so you can move the stack forward or back a little bit.&nbsp; My experience is that the old holes are usually in the right place.&nbsp; </DIV>
<DIV>&nbsp;&nbsp;&nbsp;&nbsp;I figure that&nbsp;the stack is where it needs to be when the hammers check properly.&nbsp; You want to make sure that the height of the stack is correct.&nbsp; Chisel off the splinters from around the screw holes so that the brackets sit squarely on the bracket supports (feet?).&nbsp; Be sure to check the bedding of the keyframe (if you start the bedding from scratch, you may be doing a LOT of key levelling, dip, all&nbsp;9 yards of regulation.)&nbsp; You will likely find that the inner brackets sit a little&nbsp;higher off the keyframe, so shim as necessary.&nbsp; After you screw the stack down, check to see that the hammer rail is still straight.&nbsp; Without shimming, you may see it bow in the middle.&nbsp; If your stack height is correct, and the fore/aft adjustment is correct, the regulation should come back&nbsp;into line (except if someone did a lot of letoff adjustments).</DIV>
<DIV>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; If you plan to bill Young Chang, know that they are offering only $150. for the job.&nbsp; </DIV>
<DIV>&nbsp;&nbsp;&nbsp;&nbsp;YMMV.&nbsp; Good luck.</DIV>
<DIV>&nbsp;&nbsp;&nbsp;&nbsp;Paul McCloud</DIV>
<DIV>&nbsp;&nbsp;&nbsp;&nbsp;San Diego</DIV>
<DIV>&nbsp;</DIV>
<DIV></DIV></DIV>
<DIV>&nbsp;</DIV>
<BLOCKQUOTE style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid">
<DIV style="FONT: 10pt Arial">----- Original Message ----- </DIV>
<DIV style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B> <A title=jhjpiano@sbcglobal.net href="mailto:jhjpiano@sbcglobal.net">Jim Johnson</A> </DIV>
<DIV style="FONT: 10pt arial"><B>To: </B><A title=pianotech@ptg.org href="mailto:pianotech@ptg.org">Pianotech List</A></DIV>
<DIV style="FONT: 10pt arial"><B>Sent:</B> 05/28/2007 10:06:28 AM </DIV>
<DIV style="FONT: 10pt arial"><B>Subject:</B> YC bracket installation</DIV>
<DIV><BR></DIV><FONT size=2>
<DIV><FONT face=Arial size=2></FONT>&nbsp;</DIV>
<BLOCKQUOTE dir=ltr style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV style="FONT: 10pt arial">I will be installing a set of Young Chang grand action brackets and wanted to see if any of you have any better ideas than I have about how to insure proper positioning of the brackets to insure a&nbsp;correct hammer line and capstan alignment.</DIV></BLOCKQUOTE></FONT></BLOCKQUOTE></BODY></HTML>