<br><font size=2 face="sans-serif">Dean,</font>
<br>
<br><font size=2 face="sans-serif">I think the G3 is similar to the C2.
Interesting point about the super glue. &nbsp;May have to try it sometime...</font>
<br>
<br><font size=2 face="sans-serif">PTW</font>
<br>
<br>
<br>
<br>
<table width=100%>
<tr valign=top>
<td width=40%><font size=1 face="sans-serif"><b>&quot;Dean May&quot; &lt;deanmay@pianorebuilders.com&gt;</b>
</font>
<br><font size=1 face="sans-serif">Sent by: pianotech-bounces@ptg.org</font>
<p><font size=1 face="sans-serif">01/10/2008 08:18 AM</font>
<table border>
<tr valign=top>
<td bgcolor=white>
<div align=center><font size=1 face="sans-serif">Please respond to<br>
Pianotech List &lt;pianotech@ptg.org&gt;</font></div></table>
<br>
<td width=59%>
<table width=100%>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">To</font></div>
<td><font size=1 face="sans-serif">&quot;'Pianotech List'&quot; &lt;pianotech@ptg.org&gt;</font>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">cc</font></div>
<td>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">Subject</font></div>
<td><font size=1 face="sans-serif">RE: Yamaha G3</font></table>
<br>
<table>
<tr valign=top>
<td>
<td></table>
<br></table>
<br>
<br>
<br><font size=2 color=#000080 face="Arial">I’m not familiar with this
particular model, but I have done screws in similar situations. You can
get screwdrivers that hold the screw on the end while you stick it into
inaccessible places. In a pinch you can also super glue the screw to the
end of your screwdriver. Once you start putting torque on it it will break
loose. </font>
<br><font size=2 color=#000080 face="Arial">&nbsp;</font>
<br><font size=5 color=#000080 face="Bradley Hand ITC"><b>Dean</b></font>
<br><font size=3 color=#000080 face="Times New Roman">Dean May &nbsp; &nbsp;
&nbsp; &nbsp; &nbsp; &nbsp; cell 812.239.3359 </font>
<br><font size=3 color=#000080 face="Times New Roman">PianoRebuilders.com
&nbsp; 812.235.5272 </font>
<br><font size=3 color=#000080 face="Times New Roman">Terre Haute IN &nbsp;47802</font>
<div align=center>
<br>
<hr></div>
<br><font size=2 face="Tahoma"><b>From:</b> pianotech-bounces@ptg.org [mailto:pianotech-bounces@ptg.org]
<b>On Behalf Of </b>Rex Roseman<b><br>
Sent:</b> Wednesday, January 09, 2008 8:07 PM<b><br>
To:</b> 'Pianotech List'<b><br>
Subject:</b> Yamaha G3</font>
<br><font size=3 face="Times New Roman">&nbsp;</font>
<br><font size=2 face="Arial">Dear List</font>
<br><font size=2 face="Arial">&nbsp;</font>
<br><font size=2 face="Arial">I have a problem with a Yamaha G3 grand.
The flange screw for the center damper lifter tray flange has come loose
and is out of its hole. (This is the screw that holds the flange to the
damper flange rail, not the screw that attaches it to the damper lifter
tray.) When it works its way around it gets between the damper tray and
the damper flange rail and holds the tray up just enough for the bass most
dampers to not stop the strings correctly. I remember seeing descriptions
on this list for a tool to tighten the end flange screws, but I’m not
sure if this can get to the center flange screw. The screw is not just
loose where it can be just tightened; I am going to have to get it restarted
into the aluminum flange rail.</font>
<br><font size=2 face="Arial">&nbsp;</font>
<br><font size=2 face="Arial">Even if the entire back action was disassembled,
I don’t see anyway that this screw could ever have been installed to begin
with unless it was put in before the keybed was installed. Any and all
help will be much appreciated.</font>
<br><font size=2 face="Arial">&nbsp;</font>
<br><font size=2 face="Arial">Thanks</font>
<br><font size=2 face="Arial">&nbsp;</font>
<br><font size=2 face="Arial">Rex Roseman</font>
<br><font size=2 face="Arial">Roseman Piano Tuning</font>
<br>