<br><font size=2 face="sans-serif">What's it doing in MO? &nbsp;We're sunny
and near 70 in Lincoln! &nbsp;</font>
<br>
<br>
<br>
<br>
<table width=100%>
<tr valign=top>
<td width=40%><font size=1 face="sans-serif"><b>&quot;Alan Barnard&quot;
&lt;pianotuner@embarqmail.com&gt;</b> </font>
<br><font size=1 face="sans-serif">Sent by: pianotech-bounces@ptg.org</font>
<p><font size=1 face="sans-serif">04/16/2008 11:21 AM</font>
<table border>
<tr valign=top>
<td bgcolor=white>
<div align=center><font size=1 face="sans-serif">Please respond to<br>
pianotuner@embarqmail.com; Please respond to<br>
Pianotech List &lt;pianotech@ptg.org&gt;</font></div></table>
<br>
<td width=59%>
<table width=100%>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">To</font></div>
<td><font size=1 face="sans-serif">pianotech@ptg.org</font>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">cc</font></div>
<td>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">Subject</font></div>
<td><font size=1 face="sans-serif">OT Shivering comment was RE: Spring
Time</font></table>
<br>
<table>
<tr valign=top>
<td>
<td></table>
<br></table>
<br>
<br>
<br><tt><font size=2>Speaking of Springtime .... I sure hope Algore solves
this global warming &quot;problem&quot; before we all freeze to death here
in the Midwest.<br>
<br>
Alan Barnard<br>
Salem, MO<br>
<br>
----- Original message ----------------------------------------<br>
From: &quot;Jon Page&quot; &lt;jonpage@comcast.net&gt;<br>
To: pianotech@ptg.org<br>
Received: 4/16/2008 10:27:57 AM<br>
Subject: Spring Time<br>
<br>
<br>
&gt;I finally received some phosphor-bronze spring wire: .022, .028, .032.<br>
<br>
&gt;I made a few springs by hand with a hinge pin mounted in a vise to
form<br>
&gt;the coil but am interested in what is a suitable spring making tool.
Possibly<br>
&gt;the one listed in the Schaff catalogue or someone's fabrication. Ideas?
Pix??<br>
<br>
&gt;The springs I made are for a back action underlever assist.<br>
&gt;I made 16 of .032 for the lowest ones and 8 of .022 for the highest.<br>
<br>
&gt;The supplied springs (.026) always seemed a little strained on the
lower<br>
&gt;end so I made springs with a heavier gage. I like to set the tension
lighter<br>
&gt;at the high end of the spring section so as not to have a large weight
change<br>
&gt;at the transition to non-assisted underlevers and the lighter gage
allows<br>
&gt;for a firmer/positive positioning in the slot while offering less force.<br>
<br>
&gt;Also, I'll be making different wippen assist springs. The arm which
attaches<br>
&gt;to the loop is too short and strained at rest. I've done some experimentation<br>
&gt;and found that a longer arm has a more fluid feel to it's affect and
there is<br>
&gt;less of a tension change from rest to full key stroke. And according
to<br>
&gt;Ron O, they need an extra coil. &nbsp;I have a S&amp;S M in the shop
which I'll be<br>
&gt;needing a spring making tool to do just this.<br>
&gt;-- <br>
<br>
&gt;Regards,<br>
<br>
&gt;Jon Page<br>
</font></tt>
<br>