<html xmlns:v="urn:schemas-microsoft-com:vml" xmlns:o="urn:schemas-microsoft-com:office:office" xmlns:w="urn:schemas-microsoft-com:office:word" xmlns:st1="urn:schemas-microsoft-com:office:smarttags" xmlns="http://www.w3.org/TR/REC-html40"> <head> <META HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=us-ascii"> <meta name=Generator content="Microsoft Word 11 (filtered medium)"> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="PostalCode"/> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="State"/> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="City"/> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="place"/> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="PersonName"/>  <style>  </style> </head> <body lang=EN-US link=blue vlink=purple> <div class=Section1> Simple question that has evoked vigorous discussion before. Hey, it’s an opinionated list. ;-)<o:p></o:p> <o:p> </o:p> I give an 8 year full warranty and charge 2.5 to 3 times my tuning fee. The warranty is a value added service that people are willing to pay for- just like paying extra for a used car warranty. I’ve had problem child pins rarely and for those I just give them more attention. So far I’ve always had success with pulling the pin all the way out, squirting CA directly into the hole and reinserting the pin. If I should ever encounter a piano that I could not nurse for 8 years I am fully prepared to refund the money. <o:p></o:p> <o:p> </o:p> <div> Dean<o:p></o:p> <u1:PERSONNAME u2:st="on">Dean May</u1:PERSONNAME>             cell 812.239.3359 <o:p></o:p> PianoRebuilders.com   812.235.5272 <o:p></o:p> <u1:PLACE u2:st="on"><u1:CITY u2:st="on"><st1:place w:st="on"><st1:City w:st="on"><u3:place u4:st="on"><u3:City u4:st="on">Terre Haute</st1:City></u3:place></u1:CITY></u3:City> <u1:STATE u2:st="on"><st1:State u5:st="on"><st1:State w:st="on">IN</st1:State></u1:STATE></st1:State>  <u1:POSTALCODE u2:st="on"><st1:PostalCode u6:st="on"><st1:PostalCode w:st="on">47802</st1:PostalCode></u1:POSTALCODE></st1:PostalCode></st1:place></u1:PLACE><o:p></o:p> </div> <o:p> </o:p> <div> <div class=MsoNormal align=center style='text-align:center'> <hr size=2 width="100%" align=center tabindex=-1> </div> From: pianotech-bounces@ptg.org [mailto:pianotech-bounces@ptg.org] On Behalf Of Matthew Todd Sent: Tuesday, June 10, 2008 8:47 AM To: <st1:PersonName w:st="on">Pianotech List</st1:PersonName> Subject: Re: Pin bushings with CA glue application<o:p></o:p> </div> <o:p> </o:p> <div> What kind of warranty do ya'll put on this procedure?<o:p></o:p> </div> <div>  <o:p></o:p> </div> <div> Matthew "William R. Monroe" <pianotech@a440piano.net> wrote:<o:p></o:p> </div> <blockquote style='border:none;border-left:solid #1010FF 1.5pt;padding:0in 0in 0in 4.0pt; margin-left:3.75pt;margin-top:5.0pt;margin-bottom:5.0pt'> Gordon, Just a quick note from the "less is more" school of thought. Though I'm sure I'm not as minimal as some in this procedure, I tend toward using less CA. Probably my biggest reason for doing so is mess/potential for damage. For starters, I have yet to tip an upright for application. Capillary action works quite well without tipping. And, more importantly for me, I have no worries about CA running down the plate/strings/whatever. Once capillary action fails to draw in any more CA, you know you're done. It takes a couple to get the hang of seeing that you're almost there to avoid dripping, but if you go slow to start, you'll get it pretty fast. Still, wise men still have paper towels handy.......and debonder. I also tend to work in two passes. William R. Monroe > Hi Gordon: > I have treated around 60 pianos with CA, both with and without > bushings. Your first application will soak into the bushings and the > excess will run seep down into the pinblock. Be generous. Go around a > second time (which I do most times anyway) and that will insure that CA > will wick down into the block where you want it. My philosophy is more is > better. I don't want to come back later and reapply because I was stingy > with the product the first time. > If it is a grand, play it safe and remove the action to prevent seepage > past the pins. In a spinet like yours, before you flip the piano up on > all four, be sure any excess has been soaked up with paper toweling as it > can run down the strings and into the dampers. Ask me how I know..... > Good Luck > Mike Kurta > > <o:p></o:p> </blockquote> <o:p> </o:p> </div> </body> </html>