<html xmlns:m="http://schemas.microsoft.com/office/2004/12/omml">
<head>
<META HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=us-ascii">
<meta name=Generator content="Microsoft Word 10 (filtered)">
<title>[CAUT] hammer thickness trimming jig</title>
<style>
<!--a:link
        {mso-style-priority:99;}
span.MSOHYPERLINK
        {mso-style-priority:99;}
a:visited
        {mso-style-priority:99;}
span.MSOHYPERLINKFOLLOWED
        {mso-style-priority:99;}
pre
        {mso-style-priority:99;}
span.HTMLPREFORMATTEDCHAR
        {mso-style-priority:99;}
/* Font Definitions */
@font-face
        {font-family:Calibri;}
@font-face
        {font-family:Consolas;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
        {margin:0in;
        margin-bottom:.0001pt;
        font-size:12.0pt;
        font-family:"Times New Roman";}
a:link, span.MsoHyperlink
        {color:blue;
        text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
        {color:purple;
        text-decoration:underline;}
p
        {margin-right:0in;
        margin-left:0in;
        font-size:12.0pt;
        font-family:"Times New Roman";}
pre
        {margin:0in;
        margin-bottom:.0001pt;
        font-size:10.0pt;
        font-family:"Courier New";}
span.HTMLPreformattedChar
        {font-family:Consolas;}
span.EmailStyle19
        {font-family:Calibri;
        color:#1F497D;}
span.EmailStyle20
        {font-family:Arial;
        color:navy;}
@page Section1
        {size:8.5in 11.0in;
        margin:1.0in 1.0in 1.0in 1.0in;}
div.Section1
        {page:Section1;}
-->
</style>
</head>
<body lang=EN-US link=blue vlink=purple>
<div class=Section1>
<p class=MsoNormal><font size=2 color=navy face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:navy'>Table saws and routers always make me a
bit nervous especially when trying to support the object in question with hand
held pressure. It seems like one could construct a jig where the hammer
is held strike point down so that the shank doesn’t actually get in the
way and you could create some kind of holding mechanism so fingers or finger
pressure to hold things in place would not need to be used. The width of
the hammer could thus be thinned and weight removed to the point just before
where the shank engages. A belt sander could then be used to clean up the
area around the shank were it necessary. I’ll have to give it some
thought when the shop empties of pianos (which isn’t likely any time
soon). It might be easier just to remove the offending set from the
shanks, thin them on the Spurlock jig and rehang them. The customer is
paying, after all. Why put your fingers at risk to save them a few
bucks. </span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:navy'> </span></font></p>
<div>
<p><font size=2 color=navy face="Times New Roman"><span style='font-size:10.0pt;
color:navy'>David Love<br>
davidlovepianos@comcast.net<br>
www.davidlovepianos.com</span></font><font color=navy><span style='color:navy'>
</span></font></p>
</div>
<p class=MsoNormal style='margin-left:.5in'><font size=3 face="Times New Roman"><span
style='font-size:12.0pt'> </span></font></p>
</div>
</body>
</html>