<font color='black' size='2' face='Georgia, Times New Roman, Times, Serif'><font class="Apple-style-span" size="2">&nbsp; &nbsp; &nbsp; &nbsp; I don't see how shimming anything in the action cavity is going to reduce the free play between the pedal rod and the keyframe( unless you mean shimming the keyframe. &nbsp;You have two &nbsp; pivots here, and leather between all. &nbsp;Where to take up the slack? &nbsp;I think it best if you have the shift lever parallel to the bottom of the keybed, so that upon rotation, the short arm will push the keyframe as much sideways as possible, with any rotational effect working to push down on the keyframe rather than up. &nbsp;You may need to bolster the contact point on the keyframe, or add leather at the top of the pedal rod, or check to see that all the pedals are in the same plane, since you may have used thinner pedal cushions, which will introduce a lot of slack.&nbsp;</font>
<div><font class="Apple-style-span" size="2">Regards,&nbsp;<br>
</font><br>

<div style="font-size: 13px; clear: both; "><font color="black" face="arial" size="2">Ed Foote RPT<br>
http://www.piano-tuners.org/edfoote/index.html</font></div>
<br>
&nbsp;<br>

<div style="font-family: helvetica, arial; font-size: 10pt; color: black; ">






<div id="AOLMsgPart_1_14544b9f-9a58-4525-b80f-7ce2e47013ee">

<font color="black" size="2" face="Arial, Helvetica, sans-serif">

<div style="FONT-FAMILY: arial,helvetica; COLOR: black; FONT-SIZE: 10pt">


<div><font color="black" size="2" face="Arial, Helvetica, sans-serif">I've rebuilt the piano, The old leather on the trap system has been removed and replaced with new leather. The cavity where the shift pedal activates the action is all there, and doesn't look worn out. The action shifts correctly. It's just that&nbsp;when you press the shift pedal, there is about 1/2" of lost motion. I can, and have, added another layer of leather, which reduced the gap, and the shift does move over a little sooner. (It stops at&nbsp;the action shift screw.&nbsp;</font></div>




<div><font color="black" size="2" face="Arial, Helvetica, sans-serif"></font>&nbsp;</div>




<div><font color="black" size="2" face="Arial, Helvetica, sans-serif">My question was if anyone has ever shimmed the action cavity to take care of the gap, or is adding leather the best solution?</font></div>




<div><font color="black" size="2" face="Arial, Helvetica, sans-serif"></font>&nbsp;</div>




<div><font color="black" size="2" face="Arial, Helvetica, sans-serif">Wim&nbsp;<br>

<br>

</font></div>
<font color="black" size="2" face="Arial, Helvetica, sans-serif">



<div style="CLEAR: both">


<div>&nbsp;</div>
</div>

<div style="FONT-FAMILY: arial,helvetica; COLOR: black; FONT-SIZE: 10pt">
<div id="AOLMsgPart_1_192884e5-ad70-421a-be9d-a5ab7aee19cc"><font color="black" size="2" face="Georgia, Times New Roman, Times, Serif">
<div>
<div style="COLOR: black; FONT-SIZE: 10pt">
<div id="AOLMsgPart_1_adf4e368-2b6f-4872-95dd-4f6e1aa86c8f"><blockquote style="BORDER-LEFT: rgb(0,0,0) 2px solid; PADDING-LEFT: 5px; PADDING-RIGHT: 0px; MARGIN-LEFT: 5px; MARGIN-RIGHT: 0px" dir="ltr"><font style="FONT-FAMILY: helvetica, arial" color="black" size="2" face="Arial, Helvetica, sans-serif">
<div style="CLEAR: both">
</div>

</font></blockquote></div>

</div>

</div>

</font></div>

</div>

</font></div>

</font>
</div>
 <!-- end of AOLMsgPart_1_14544b9f-9a58-4525-b80f-7ce2e47013ee -->



</div>
</div>
</font>