<span class="Apple-style-span" style="font-family:Verdana,Geneva,Arial,Helvetica,sans-serif;font-size:13px">Hi Mike,</span><br style="line-height:1.22em;font-family:Verdana,Geneva,Arial,Helvetica,sans-serif;font-size:13px;text-align:left">
<br style="line-height:1.22em;font-family:Verdana,Geneva,Arial,Helvetica,sans-serif;font-size:13px;text-align:left"><span class="Apple-style-span" style="font-family:Verdana,Geneva,Arial,Helvetica,sans-serif;font-size:13px;text-align:left">Sure.  A pegged mortise and tenon is a pretty cool joint.  Can&#39;t say I&#39;ve seen it in a piano before, but elsewhere.  The design is to offset the hole in the tenon just slightly, so that when the peg is driven in, it tightens the joint fully.  Prior to drilling, the two pieces can be clamped together, then using an undersized transfer punch, hold it to the bottom of the hole in the capital (top piece of the lyre) and mark for drilling.  Then after you have drilled, a new tapered dowel should pull the assembly together nicely.</span><br style="line-height:1.22em;font-family:Verdana,Geneva,Arial,Helvetica,sans-serif;font-size:13px;text-align:left">
<br style="line-height:1.22em;font-family:Verdana,Geneva,Arial,Helvetica,sans-serif;font-size:13px;text-align:left"><span class="Apple-style-span" style="font-family:Verdana,Geneva,Arial,Helvetica,sans-serif;font-size:13px;text-align:left">It&#39;s likely that whomever installed the machine screws enlarged both holes and goofed up the otherwise elegant design.</span><div>
<div style="text-align:left"><font class="Apple-style-span" face="Verdana, Geneva, Arial, Helvetica, sans-serif"><br></font></div><div style="text-align:left"><font class="Apple-style-span" face="Verdana, Geneva, Arial, Helvetica, sans-serif">William R. Monroe</font></div>
<div style="text-align:left"><font class="Apple-style-span" face="Verdana, Geneva, Arial, Helvetica, sans-serif"><br></font></div><div style="text-align:left"><font class="Apple-style-span" face="Verdana, Geneva, Arial, Helvetica, sans-serif"><br>
</font></div><br><div class="gmail_quote">On Mon, Dec 12, 2011 at 3:39 PM, Mike Spalding <span dir="ltr">&lt;<a href="mailto:mike.spalding1@frontier.com">mike.spalding1@frontier.com</a>&gt;</span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
I brought home a Kimball lyre to repair:  loose joints, top and bottom.  The lower joints (post to pedal box) were more or less conventional round tenons, on which the epoxy is currently curing.  The top joint is one I&#39;ve never seen in a piano before.  Did I mention the piano is a former player?  Anyway, the post has a square tenon which fits very loosely into a 3-sided mortice in the top block, and is secured with a tapered dowel.  Well, it was at one time.  The tapered dowels had been replaced with steel machine screws, so the whole thing was really floppy.  I roughed out a couple of tapered dowels and fitted them in the holes, and I&#39;m not satisfied with the way the joint fits together.  The main problem is that with the dowels in place, the top block is held almost 2mm above the shoulders of the posts.  I&#39;m considering whether to plug and re-drill the dowel holes in the posts, or build up the block to meet the shoulders.  I&#39;m also considering drilling out the tapered holes and using a straight dowel.  Anybody ever seen this joint before?  Any insights or free advice?<br>

<br>
thanks<span class="HOEnZb"><font color="#888888"><br>
<br>
Mike<br>
</font></span></blockquote></div><br><br clear="all"><div><br></div>
</div>