<font color='navy' size='2' face='Comic Sans MS, sans-serif'>It<font color="navy" face="Comic Sans MS, sans-serif" size="2"> could be&nbsp; a number of things and some that are hard to put your finger on. It could be glue quality, or age. Felt is hygroscopic and can absorb excess moisture in humid season prior to glue up if not monitored and could contribute to failure<br>
&nbsp;Inadequate amounts of glue applied to the felt and wood, or removal from the press before the glue adequately set. And,... some times the felt is just dang strong. There is an enormous amount of stretch and pull that the felt can exhibit on the joint especially in the low bass after the felt has been tensioned stretched and compressed onto the molding.<br>
&nbsp;&nbsp; I've talked to Ray Negron/Ronsen and sometimes the reasons are unknown. Certain woods are more problematic too. The Weickert felt is so Strong that we've gone to 2 staples in the low bass mon-chords and it really helps<br>
Dale<br>

<br>



<div style="clear:both"><font color="royalblue" size="1"><b><font face="Georgia, Times New Roman, Times, Serif"><font color="black"><font color="mediumblue" face="Comic Sans MS, sans-serif">Dale Erwin RPT-</font><br>

</font></font></b></font><font color="royalblue" size="1"><font color="blueviolet"><b><font color="black" size="2"><font size="1"></font></font></b></font></font><font color="darkgreen"><span style="font-style: italic;"><b><font size="1"><font color="black"><font color="blueviolet"><font color="black"> <font color="black">Mason &amp; Hamlin</font>/Steinway/<font color="black">U.S pianos</font><br>

</font><font color="mediumblue">Pre-hung Ronsen hammer sets/Abel parts</font></font><br>

</font>Sitka Soundboards &amp; Supplies<br>

<font color="black">WWW.Erwinspiano.com</font><br>

<font color="crimson">209-577-8397</font><br>

<font color="darkgreen"></font></font></b></span></font><tt><tt><font color="darkgreen"><br>

&nbsp;</font><br>

&nbsp; <font size="2"></font></tt></tt><br>

<br>

</div>

<br>

<br>



<div style="font-family:arial,helvetica;font-size:10pt;color:black">-----Original Message-----<br>

From: atrav27 &lt;atrav27@att.net&gt;<br>

To: pianotech &lt;pianotech@ptg.org&gt;<br>

Sent: Mon, Feb 13, 2012 6:16 pm<br>

Subject: Re: [pianotech] re-gluing loose hammer felt<br>

<br>









<div id="AOLMsgPart_0_765d1ca5-2fe9-496b-85f6-0a9563c62df4" style="margin: 0px;font-family: Tahoma, Verdana, Arial, Sans-Serif;font-size: 12px;color: #000;background-color: #fff;">

<pre style="font-size: 9pt;"><tt>
----- Original Message ----- 
From: "Wally Scherer" &lt;<a href="mailto:afinetune@yahoo.com">afinetune@yahoo.com</a>&gt;

It was a Baldwin studio with about 20 hammers half separated. 
===========

What are the most likely causes of hammer felt letting go anyway?
Preventable?

-Aron-
</tt></pre>
</div>

 <!-- end of AOLMsgPart_0_765d1ca5-2fe9-496b-85f6-0a9563c62df4 -->



</div>

</font></font>