<font color='navy' size='2' face='Comic Sans MS, sans-serif'><font size="2"><font face="Comic Sans MS, sans-serif"><br>
&nbsp;Joe<br>
&nbsp;One of the nicest parts about acrylic lacquer is they are quite flexible for some time. The screw holes clean out easily with a sharp counter sink. Its not brittle and you gotta whack it, or scratch it hard to really mess it up. Down side is, if you get it too thick the washers and rear aliquots tend to bury into the lacquer a bit.<br>
Will? ...Hows yer finish on these issues<br>
<br>
</font></font><font size="2" color="navy" face="Comic Sans MS, sans-serif"><font size="1" color="royalblue"><b><font face="Georgia, Times New Roman, Times, Serif"><font color="black"><font color="mediumblue" face="Comic Sans MS, sans-serif">Dale Erwin... RPT</font><br>

</font></font></b></font><font color="darkgreen"><span style="font-style: italic;"><b><font size="1"><font color="black"><font color="blueviolet"><font color="black"> <font color="black" face="Comic Sans MS, sans-serif">Mason &amp; Hamlin</font><font face="Comic Sans MS, sans-serif">/Steinway/</font><font color="black" face="Comic Sans MS, sans-serif">U.S pianos</font><font face="Comic Sans MS, sans-serif"><br>

</font></font></font></font><font color="black" face="Comic Sans MS, sans-serif">www.Erwinspiano.com</font><br>

<font color="crimson" face="Comic Sans MS, sans-serif">209-577-8397</font></font></b></span></font></font><br>
<font size="2"><font face="Comic Sans MS, sans-serif"><br>
</font></font>Will,
Excellent write-up. I printed it out to show to my refinisher.&lt;G&gt; Just
wondering how this stuff is in regard to "chipping". I've yet to find any
finish that will resist chipping unless it is less than a week old, (i.e.
still soft ). I've found that using an appropriate counter sink on the
screw holes, right after the initial finishing process, helps to eliminate
some chipping, but ya really have to have all your ducks in a row to get
the plate stuffed into the carcus and get the strings on before the darned
stuff sets up hard. Any suggestions?
Regards,
Joe


Joe Garrett, R.P.T.
Captain of the Tool Police
Squares R I

<font size="2" color="navy" face="Comic Sans MS, sans-serif"><br>

<br>



<div style="clear:both"><font color="darkgreen"><span style="font-style: italic;"><b><font size="1"><font color="crimson" face="Comic Sans MS, sans-serif"></font><br>

</font></b></span></font>From: Joseph Garrett &lt;joegarrett@earthlink.net&gt;<br>

<font size="2" color="navy" face="Comic Sans MS, sans-serif"><br>
</font><br>
<tt><tt><font color="darkgreen">
&nbsp;</font><br>

&nbsp; </tt></tt><br>

<br>

</div>

<br>

<br>



<div style="font-family:arial,helvetica;font-size:10pt;color:black"><tt></tt>
<div id="AOLMsgPart_0_1fc878b5-8147-4581-afc0-d2d69a892e27" style="margin: 0px;font-family: Tahoma, Verdana, Arial, Sans-Serif;font-size: 12px;color: #000;background-color: #fff;">
</div>

 <!-- end of AOLMsgPart_0_1fc878b5-8147-4581-afc0-d2d69a892e27 -->



</div>

</font></font>