<font color='navy' size='2' face='Comic Sans MS, sans-serif'><font color="#000080" face="Comic Sans MS, sans-serif" size="2">Gary</font><br>

<div><font color="#000080" face="Comic Sans MS, sans-serif" size="2">&nbsp; &nbsp;As my Dad used to say"Frustratin.... ain't it?"</font></div>

<div><font color="#000080" face="Comic Sans MS, sans-serif" size="2">&nbsp; Screw the bedding bolts up so they no longer touch the keybed. Then there is a bit of spring in the action frame. You may be able to push down on the balance rail and pull out at the same time.&nbsp;</font><font color="#000080" face="Comic Sans MS, sans-serif">Other</font><font color="#000080" face="Comic Sans MS, sans-serif" size="2">&nbsp;than that use a hammer and a punch and see if you can fracture the brackets and remove the action</font><br>
<br>

<div style="color: navy; font-family: 'Comic Sans MS', sans-serif; font-size: 10pt; clear: both; "><font size="1" color="royalblue"><b><font face="Georgia, Times New Roman, Times, Serif"><font color="black"><font color="mediumblue" face="Comic Sans MS, sans-serif">Dale Erwin R.P.T.<br>
<font color="green">Erwin's Piano Restoration Inc.</font><br>
</font></font></font></b></font><font color="darkgreen"><span style="font-style: italic;"><b><font size="1"><font size="1" color="black"><font color="blueviolet"><font color="black"> <font color="black" face="Comic Sans MS, sans-serif">Mason &amp; Hamlin</font><font face="Comic Sans MS, sans-serif">/Steinway/</font><font color="black" face="Comic Sans MS, sans-serif">U.S. pianos</font><font face="Comic Sans MS, sans-serif"><br>
</font></font></font></font><font size="1" color="cornflowerblue" face="Comic Sans MS, sans-serif">www.Erwinspiano.com</font><font size="1"><br>
</font><font size="1" color="crimson" face="Comic Sans MS, sans-serif">Phone: 209-577-8397</font><br>
<font color="darkgreen"></font></font></b></span></font><tt><tt><font color="darkgreen"><br>
&nbsp;</font><br>
&nbsp; <font size="2"></font></tt></tt><br>
<br>
</div>
<br>
<br>

<div style="color: black; font-family: arial, helvetica; font-size: 10pt; ">-----Original Message-----<br>
From: Gary &lt;gmcc@charter.net&gt;<br>
To: pianotech &lt;pianotech@ptg.org&gt;<br>
Sent: Tue, Sep 4, 2012 5:57 pm<br>
Subject: [pianotech] stuck action<br>
<br>







<div id="AOLMsgPart_0_c88fbe9e-01d5-46c7-901c-3038b43886b8" style="margin: 0px;font-family: Tahoma, Verdana, Arial, Sans-Serif;font-size: 12px;color: #000;background-color: #fff;">

<pre style="font-size: 9pt;"><tt>A Wurlitzer grand with the Young Chang growing action brackets.  I have 
the brackets to replace them, but can't pull the action out,
the drop screws on the extreme ends are touching the pin block.  I seem 
to recall some techs having this problem, but I can't remember their
solution.  Any suggestions?
thanks
gary

</tt></pre>
</div>
 <!-- end of AOLMsgPart_0_c88fbe9e-01d5-46c7-901c-3038b43886b8 -->



</div>
</div>
</font>