<html xmlns:v="urn:schemas-microsoft-com:vml" xmlns:o="urn:schemas-microsoft-com:office:office" xmlns:w="urn:schemas-microsoft-com:office:word" xmlns:st1="urn:schemas-microsoft-com:office:smarttags" xmlns="http://www.w3.org/TR/REC-html40"> <head> <meta http-equiv=Content-Type content="text/html; charset=us-ascii"> <meta name=Generator content="Microsoft Word 11 (filtered medium)"> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="PostalCode"/> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="State"/> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="place"/> <o:SmartTagType namespaceuri="urn:schemas-microsoft-com:office:smarttags" name="City"/>  <style>  </style>  </head> <body lang=EN-US link=blue vlink=purple style='word-wrap: break-word; -webkit-nbsp-mode: space;-webkit-line-break: after-white-space'> <div class=Section1> Terry, is that you on the right without the shirt? I like the beard. <o:p></o:p> <o:p> </o:p> <div> Dean<o:p></o:p> Dean W May                (812) 235-5272 voice and text <o:p></o:p> PianoRebuilders.com    (888) DEAN-MAY        <o:p></o:p> <ST1:PLACE u1:st="on"><u4:CITY u1:st="on"><u2:place u3:st="on"><u2:City u3:st="on"><st1:place w:st="on"><st1:City w:st="on">Terre Haute</st1:City></u2:place></st1:place></u4:CITY> <U2:STATE u1:st="on"><u2:State u3:st="on"><st1:State w:st="on">IN</u2:State></u2:State></U2:STATE></st1:State> <U2:POSTALCODE u1:st="on"><u2:PostalCode u3:st="on"><st1:PostalCode w:st="on">47802</u2:PostalCode></u2:PostalCode></U2:POSTALCODE></st1:PostalCode></st1:place><o:p></o:p> </div> </ST1:PLACE> <div> <div class=MsoNormal align=center style='text-align:center'> <hr size=2 width="100%" align=center tabindex=-1> </div> From: pianotech-bounces@ptg.org [mailto:pianotech-bounces@ptg.org] On Behalf Of Terry Farrell Sent: Saturday, September 08, 2012 9:58 AM To: pianotech@ptg.org Subject: Re: [pianotech] Repair to console music desk<o:p></o:p> </div> <o:p> </o:p> <div> <img width=500 height=333 id=bf917919-4133-4ebb-8159-dc5a255e8f50 src="cid:image001.jpg@01CD8ED4.16D9DD00" apple-width=yes apple-height=yes><o:p></o:p> </div> <div> <o:p> </o:p> </div> <div> Terry Farrell<o:p></o:p> </div> <o:p> </o:p> <div> <div> On Sep 7, 2012, at 11:23 AM, Susan Kline wrote:<o:p></o:p> </div> <o:p></o:p> <div bgcolor="#ffffff" text="#000000"> I think what is "best" depends on how bad the break is and what situation the piano is in. One decent repair of this inherently fragile system which I've seen is a strip of brass about two inches long, screwed into the back of the music desk, which bends around the end. Three holes, two for the screws into the back of the desk, and one which is just big enough for the end screw to go through. I'd put epoxy into the splits and let it set up before installing the brass. If I remember right, I've seen this setup factory original as well. If I'm putting one of these music desks back on (without the brass strip), I always warn the owner not to tighten the screws. Always leave enough room for the music desk to move side to side a fraction of an inch. Screws into end grain -- what a lousy idea. Susan Kline Jurgen Goering wrote: <o:p></o:p> What is the "best" fix for a music desk on a console or studio upright which has been damaged at the screw pivot point?  Its funny how one good smack on the music desk, or a mere cinching up of ratchet strap in the course of a move can break the wood at the screw [tongue in cheek here]. <o:p></o:p> <div> So what is the most economical and fast in-home repair (while I tune)?  Five minute epoxy? Tightbond with a small clamp?  <o:p></o:p> </div> <div> I was thinking of calling Isaac Sadigursky but I'll try this list first...  see if anyone else knows....  :^)<o:p></o:p> </div> <div> regards,<o:p></o:p> <div> Jurgen Goering <o:p></o:p> </div> <o:p> </o:p> </div> </div> </div> <o:p> </o:p> </div> </body> </html>