<font color='navy' size='2' face='Comic Sans MS, sans-serif'><font color="#000080" face="Comic Sans MS, sans-serif" size="2">Hi Wim</font>
<div><font color="#000080" face="Comic Sans MS, sans-serif" size="2">&nbsp;Carefully!.</font>
<div><font color="#000080" face="Comic Sans MS, sans-serif" size="2">&nbsp;Voicing any set of hammers is of course a result driven process. The rule of thumb on any set of hammers that needs more sonic power is to use as little hardener as possible or only whats required. Sometime a few drops of lacquer on the strike point to produce &nbsp;little ping is all&nbsp;</font><font color="#000080" face="Comic Sans MS, sans-serif">that's</font><font color="#000080" face="Comic Sans MS, sans-serif" size="2">&nbsp;needed. WIth Yamaha hammers I'd choose the dullest note (hard to imagine) and mix up some 8 or 10 to 1 lac/acetone mix and soak the hammer top to bottom. Let it dry several hours and see if this is enough.</font></div>

<div><font color="#000080" face="Comic Sans MS, sans-serif" size="2">Of course if the board jsut lacks horsepower the end result will be simply noise. pluck strings and find out if the sustain is in there. If it is then there is something to work with.</font></div>

<div><font color="#000080" face="Comic Sans MS, sans-serif" size="2">best</font></div>

<div><font color="#000080" face="Comic Sans MS, sans-serif" size="2">Dale<br>
</font><br>

<div style="color: navy; font-family: 'Comic Sans MS', sans-serif; font-size: 10pt; clear: both;"><font size="1" color="royalblue"><b><font face="Georgia, Times New Roman, Times, Serif"><font color="black"><font color="mediumblue" face="Comic Sans MS, sans-serif">Dale Erwin R.P.T.<br>
<font color="green">Erwin's Piano Restoration Inc.</font><br>
</font></font></font></b></font><font color="darkgreen"><span style="font-style: italic;"><b><font size="1"><font size="1" color="black"><font color="blueviolet"><font color="black"> <font color="black" face="Comic Sans MS, sans-serif">Mason &amp; Hamlin</font><font face="Comic Sans MS, sans-serif">/Steinway/</font><font color="black" face="Comic Sans MS, sans-serif">U.S. pianos</font><font face="Comic Sans MS, sans-serif"><br>
</font></font></font></font><font size="1" color="cornflowerblue" face="Comic Sans MS, sans-serif">www.Erwinspiano.com</font><font size="1"><br>
</font><font size="1" color="crimson" face="Comic Sans MS, sans-serif">Phone: 209-577-8397</font><br>
<font color="darkgreen"></font></font></b></span></font><tt><tt><font color="darkgreen"><br>
&nbsp;</font><br>
&nbsp; <font size="2"></font></tt></tt><br>
<br>
</div>
<br>
<br>

<div style="color: black; font-family: arial, helvetica; font-size: 10pt;">-----Original Message-----<br>
From: tnrwim &lt;tnrwim@aol.com&gt;<br>
To: Pianotech &lt;pianotech@ptg.org&gt;<br>
Sent: Thu, Nov 29, 2012 5:57 pm<br>
Subject: [pianotech] Brighter Yamaha<br>
<br>







<div id="AOLMsgPart_0_d457495b-b466-4e99-9ccd-0cd46a27cead" style="margin: 0px;font-family: Tahoma, Verdana, Arial, Sans-Serif;font-size: 12px;color: #000;background-color: #fff;">

<pre style="font-size: 9pt;"><tt>We usually have knock the edge off Yamaha hammers. But a church just got a small 
grand where the killer octaves need a little boost.  What is the recommended 
method for "juicing" up Yamaha hammers

Wim

Sent from my iPhone
</tt></pre>
</div>
 <!-- end of AOLMsgPart_0_d457495b-b466-4e99-9ccd-0cd46a27cead -->



</div>
</div>
</div>
</font>