<font color='navy' size='2' face='Comic Sans MS, sans-serif'><font size="1">Hi Joe</font>
<div><font size="1">The question wasn't directed at me but.... Dennis &amp; I routinely install cut-offs both curved and straight and we do bevel them slightly in the appropriate direction. I'm not a big installer of the fish at this point but we do angle those a bit too. Not much as they don't need it.</font></div>

<div><font size="1">Dale</font><br>
<br>

<div style="font-size: 10pt; clear: both;"><font size="1" color="royalblue"><b><font face="Georgia, Times New Roman, Times, Serif"><font color="black"><font color="mediumblue" face="Comic Sans MS, sans-serif">Dale Erwin R.P.T.<br>
<font color="green">Erwin's Piano Restoration Inc.</font><br>
</font></font></font></b></font><font color="darkgreen"><span style="font-style: italic;"><b><font size="1"><font size="1" color="black"><font color="blueviolet"><font color="black"> <font color="black" face="Comic Sans MS, sans-serif">Mason &amp; Hamlin</font><font face="Comic Sans MS, sans-serif">/Steinway/</font><font color="black" face="Comic Sans MS, sans-serif">U.S. pianos</font><font face="Comic Sans MS, sans-serif"><br>
</font></font></font></font><font size="1" color="cornflowerblue" face="Comic Sans MS, sans-serif">www.Erwinspiano.com</font><font size="1"><br>
</font><font size="1" color="crimson" face="Comic Sans MS, sans-serif">Phone: 209-577-8397</font><br>
<font color="darkgreen"></font></font></b></span></font><tt><tt><font color="darkgreen"><br>
&nbsp;</font><br>
&nbsp; <font size="2"></font></tt></tt><br>
<br>
</div>
<br>
<br>

<div style="font-size: 10pt; font-family: arial, helvetica; color: black;">-----Original Message-----<br>
From: Joseph Garrett &lt;joegarrett@earthlink.net&gt;<br>
To: pianotech &lt;pianotech@ptg.org&gt;<br>
Sent: Tue, Dec 4, 2012 10:45 am<br>
Subject: Re: [pianotech] Belly Talk<br>
<br>







<div id="AOLMsgPart_0_d49fe49b-26cb-48cf-ab63-938c16af2d07" style="margin: 0px;font-family: Tahoma, Verdana, Arial, Sans-Serif;font-size: 12px;color: #000;background-color: #fff;">

<pre style="font-size: 9pt;"><tt>Ron said: 
"Sure, beveling the 
rasten is a reasonable presumption of necessity, but a flat rasten isn't 
the death of tone as gluing panels down to flat cutoff bars and fish 
will indicate." 

Ron,
Clarification please. Is tone compromised when the board is glued to a
cut-off and fish, if they are flat, rather than crowned? Or, do you put a
complimentary crown in the cut-off and fish? In the past, I haven't worried
about that and haven't had a problem....welll.....a percieved problem. Just
wondering.&lt;G&gt;
'Preciate it.&lt;G&gt;
Best,
Joe


Joe Garrett, R.P.T.
Captain of the Tool Police
Squares R I

</tt></pre>
</div>
 <!-- end of AOLMsgPart_0_d49fe49b-26cb-48cf-ab63-938c16af2d07 -->



</div>
</div>
</font>