<font color='navy' size='2' face='Comic Sans MS, sans-serif'><font color="#000080" face="Comic Sans MS, sans-serif" size="2">The Assembly 65(a tite-bond product is also a good glue as </font><font color="#000080" face="Comic Sans MS, sans-serif">Ron</font><font color="#000080" face="Comic Sans MS, sans-serif" size="2"> said & sets a fair bit faster than the Bolduc mystery PVA but has the same strength properties IMO. Less money too.</font><br>
<br>
<div style="color: navy; font-family: 'Comic Sans MS', sans-serif; font-size: 10pt; clear: both;"><font size="1" color="royalblue"><b><font face="Georgia, Times New Roman, Times, Serif"><font color="black"><font color="mediumblue" face="Comic Sans MS, sans-serif">Dale Erwin R.P.T.<br>
<font color="green">Erwin's Piano Restoration Inc.</font><br>
</font></font></font></b></font><font color="darkgreen"><span style="font-style: italic;"><b><font size="1"><font size="1" color="black"><font color="blueviolet"><font color="black"> <font color="black" face="Comic Sans MS, sans-serif">Mason & Hamlin</font><font face="Comic Sans MS, sans-serif">/Steinway/</font><font color="black" face="Comic Sans MS, sans-serif">U.S. pianos</font><font face="Comic Sans MS, sans-serif"><br>
</font></font></font></font><font size="1" color="cornflowerblue" face="Comic Sans MS, sans-serif">www.Erwinspiano.com</font><font size="1"><br>
</font><font size="1" color="crimson" face="Comic Sans MS, sans-serif">Phone: 209-577-8397</font><br>
<font color="darkgreen"></font></font></b></span></font><tt><tt><font color="darkgreen"><br>
</font><br>
<font size="2"></font></tt></tt><br>
<br>
</div>
<br>
<br>
<div style="color: black; font-family: arial, helvetica; font-size: 10pt;">-----Original Message-----<br>
From: Ron Nossaman <rnossaman@cox.net><br>
To: pianotech <pianotech@ptg.org><br>
Sent: Mon, Dec 10, 2012 10:51 am<br>
Subject: Re: [pianotech] Trim & Moulding Glue<br>
<br>
<div id="AOLMsgPart_0_e78b270d-acf8-4097-9f0a-faadb27a771b" style="margin: 0px;font-family: Tahoma, Verdana, Arial, Sans-Serif;font-size: 12px;color: #000;background-color: #fff;">
<pre style="font-size: 9pt;"><tt>On 12/10/2012 9:29 AM, David Love wrote:
> Chamfering the bore edge is a good idea and I do it even with the TB Trim
> that I use. I think probably the problems I see from loose hammers on jobs
> I've run into with hide glue is a viscosity issue, too thin, at least
> judging from the size, or lack of, of the collar where I see this happening.
Anything can be done badly, even with first rate materials. That doesn't
make it the materials' fault.
> I'll have to look into the Assembly 65 glue. Had not heard of that.
I've mentioned it a number of times on list. It's another Franklin
product. High solids, fast set, dries cracking hard, heat sets so would
be a good choice for high production RF cure as well as general
woodwork. Like TB 50, you can probably get it fairly cheaply from
Franklin in 5 gallon lots, or from M&H in quarts. It's an interesting
glue, and worth a try.
Ron N
</tt></pre>
</div>
<!-- end of AOLMsgPart_0_e78b270d-acf8-4097-9f0a-faadb27a771b -->
</div>
</font>