<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
<meta content="text/html;charset=ISO-8859-1" http-equiv="Content-Type">
<title></title>
</head>
<body bgcolor="#ffffff" text="#000000">
<a class="moz-txt-link-abbreviated" href="mailto:Piannaman@aol.com">Piannaman@aol.com</a> wrote:<br>
<blockquote cite="mid1dc.29c716f8.2e5ca52c@aol.com" type="cite"><font
face="arial,helvetica"><font ptsize="10" size="2">List,
<br>
<br>
While tuning a nice 1942 Baldwin L yesterday, the owner mentioned that
she had an old piano in the other room that had some notes that didn't
work, and wondered whether I could look at it and see if I could fix
it.
<br>
<br>
Turns out to be a Steinway "V" from around 1920, impeccably refinished
in deep red Mahogany. The hammers have been replaced within the last
couple of decades, but probably have never been used all that much,
given the state of the hammer-flange centers.
<br>
<br>
I didn't have to do much examining to figure out that the piano is
infested with verdigris (I forgot to note whether there are double
flanges, though :-( ).
<br>
<br>
I am going to take on the job of repinning this beast if the owners
decide they want it done, but I have a few questions. <br>
<br>
1. Will I need to replace bushings as well as the center pins? I
certainly suspect so, since the cloth is the culprit.
<br>
</font></font></blockquote>
yeppers<br>
<br>
<blockquote cite="mid1dc.29c716f8.2e5ca52c@aol.com" type="cite"><font
face="arial,helvetica"><font ptsize="10" size="2"><br>
2. Will it be cheaper/easier to just replace all of the flanges in the
piano?
<br>
</font></font></blockquote>
yeppers<br>
<blockquote cite="mid1dc.29c716f8.2e5ca52c@aol.com" type="cite"><font
face="arial,helvetica"><font ptsize="10" size="2"><br>
3. Is it likely that all of the flanges in the piano are verdigris
victims? The whippen and jack flanges don't seem to be binding, but I
would suspect that Steinway used paraffin in all of their bushing
cloth. <br>
</font></font></blockquote>
<br>
yeppers... thats a distinkt possiblity<br>
<blockquote cite="mid1dc.29c716f8.2e5ca52c@aol.com" type="cite"><font
face="arial,helvetica"><font ptsize="10" size="2"><br>
4. Time estimates from anyone who has done this project before would
be most appreciated:
<br>
A. Repinning all flanges
<br>
</font></font></blockquote>
2 hours, that will say with nicely bushed flanges laying on the table
in front of you.<br>
<blockquote cite="mid1dc.29c716f8.2e5ca52c@aol.com" type="cite"><font
face="arial,helvetica"><font ptsize="10" size="2"> B. Replacing
all flanges and subsequent fitting involved
<br>
</font></font></blockquote>
Implies repinning some of them... time consuming due to lining up the
parts.... a days work ?<br>
<blockquote cite="mid1dc.29c716f8.2e5ca52c@aol.com" type="cite"><font
face="arial,helvetica"><font ptsize="10" size="2"> C. Rebushing
and repinning all flanges
<br>
</font></font></blockquote>
A good days work.<br>
<blockquote cite="mid1dc.29c716f8.2e5ca52c@aol.com" type="cite"><font
face="arial,helvetica"><font ptsize="10" size="2"><br>
I will also consult Joe's "G" Piano Works labor guide for ETs for these
various operations.
<br>
</font></font></blockquote>
Didnt he play football for the Rams ???... quarterback... I think...
fell in love with Susanne York....?<br>
<br>
<blockquote cite="mid1dc.29c716f8.2e5ca52c@aol.com" type="cite"><font
face="arial,helvetica"><font ptsize="10" size="2"><br>
Thanks in advance for your expertise,
<br>
<br>
Dave Stahl
<br>
<br>
<br>
</font></font></blockquote>
Cheers<br>
RicB<br>
</body>
</html>