<html xmlns:o="urn:schemas-microsoft-com:office:office" =
xmlns:w="urn:schemas-microsoft-com:office:word" =
xmlns="http://www.w3.org/TR/REC-html40">
<head>
<meta http-equiv=Content-Type content="text/html; =
charset=us-ascii">
<meta name=Generator content="Microsoft Word 11 (filtered medium)">
<style>
<!--
/* Font Definitions */
@font-face
{font-family:Tahoma;
panose-1:2 11 6 4 3 5 4 4 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:12.0pt;
font-family:"Times New Roman";}
a:link, span.MsoHyperlink
{color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{color:blue;
text-decoration:underline;}
span.EmailStyle17
{mso-style-type:personal-reply;
font-family:Arial;
color:navy;}
@page Section1
{size:8.5in 11.0in;
margin:1.0in 1.25in 1.0in 1.25in;}
div.Section1
{page:Section1;}
-->
</style>
</head>
<body lang=EN-US link=blue vlink=blue id="role_body" =
bottomMargin=7
leftmargin=7 topmargin=7 rightMargin=7>
<div class=Section1>
<p class=MsoNormal><font size=2 color=navy face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:navy'><o:p> </o:p></span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:navy'><o:p> </o:p></span></font></p>
<div>
<p class=MsoNormal><b><font size=2 face=Tahoma><span =
style='font-size:10.0pt;
font-family:Tahoma;font-weight:bold'>Subject:</span></font></b><font =
size=2
face=Tahoma><span style='font-size:10.0pt;font-family:Tahoma'> Re: =
Has anybody
here had success with water-borne wood =
finishes?</span></font><o:p></o:p></p>
</div>
<p class=MsoNormal><font size=3 face="Times New Roman"><span =
style='font-size:
12.0pt'><o:p> </o:p></span></font></p>
<div>
<div>
<p class=MsoNormal><font size=2 color=black face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:black'> No recommendations =
here.
Just a miserable frustrating experience that almost caused my finisher =
to quit.
So there you have it.<o:p></o:p></span></font></p>
</div>
<div>
<p class=MsoNormal><font size=2 color=black face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:black'> =
Dale<o:p></o:p></span></font></p>
</div>
<blockquote style='border:none;border-left:solid blue =
1.5pt;padding:0in 0in 0in 4.0pt;
margin-left:3.75pt;margin-top:5.0pt;margin-bottom:5.0pt'>
<p class=MsoNormal><font size=2 color=black face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:black'>I'd like some first hand =
testimonials
about this stuff<br>
before I try it on my next peroject.<br>
Thanks!<br>
G<o:p></o:p></span></font></p>
</blockquote>
</div>
<div>
<p class=MsoNormal><font size=2 color=black face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:black'> </span></font><font size=2
color=navy face=Arial><span =
style='font-size:10.0pt;font-family:Arial;
color:navy'>Practice!</span></font><font size=2 color=black =
face=Arial><span
style='font-size:10.0pt;font-family:Arial;color:black'><o:p></o:p></spa=
n></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:navy'>I’ve done several satin =
finishes
with water based lacquer with good results, but you must practice long =
enough
to learn how to control the material with your equipment. I use a fine =
spray
nozzle and adjust the gun pressure for the results I need. The =
finish
will lay down to a level film when the gun is right. I sprayed =
straight
form the can. Each coat was allowed to dry for an hour followed by =
a
light sanding with 220 grit. Four to five coats will fill the =
pores of
walnut and mahogany. I did not wait over an hour before sanding =
and
recoating. I have seen disastrous results when the finish dried =
for
several hours and then sanded to level it. Sand through =
occurred.<o:p></o:p></span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:navy'>Homestead Finishes was the =
supplier.<o:p></o:p></span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:navy'><o:p> </o:p></span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:navy'>Paul C<o:p></o:p></span></font></p>
</div>
</div>
</body>
</html>