<!doctype html public "-//w3c//dtd html 4.0 transitional//en"> <html> <body bgcolor="#FFFFFF"> Terry, <br>    This might be a good excuse to purchase a drum sander. Performax or Delta it really doesn't matter as long as the cantilever design will accommodate most or all of the board. Of you who have made boards in the past, what width is the panel before shaping to the piano? The Delta is a bit wider so that might just make it or leave a small amount for hand or hand tool sanding or scraping. What 'chu think? <br>  <p>Greg <p>Farrell wrote: <blockquote TYPE=CITE><style></style> So then you are gluing up your 24" subpanels after they have been planed to the soundboard's final thickness (not counting edge tapering)? Can one edge glue accurately enough to get a real even subpanel-to-subpanel joint (no step from one to the other)? I was envisioning gluing up a whole soundboard panel that was thicker than needed and then (after driving the panel to a shop with BIG sanders/planers) running the whole thing through a planer device to get your nice consistent final (before tapering) thickness. If I am understanding your process, you do the above on your smaller subpanels, but then when you have glued your subpanels together, you do any slight evening up by a hand plane or sanding (or maybe even that is not needed?)? Thanks. Terry Farrell ----- Original Message ----- <blockquote dir=ltr style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px"> <div style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><b>From:</b> <a href="mailto:pianobuilders@olynet.com" title="pianobuilders@olynet.com">Delwin D Fandrich</a></div> <div style="FONT: 10pt arial"><b>To:</b> <a href="mailto:pianotech@ptg.org" title="pianotech@ptg.org">pianotech@ptg.org</a></div> <div style="FONT: 10pt arial"><b>Sent:</b> Wednesday, January 16, 2002 1:19 AM</div> <div style="FONT: 10pt arial"><b>Subject:</b> Re: my own Soundboard</div>    <blockquote style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000080 2px solid; MARGIN-RIGHT: 0px"> <div style="FONT: 10pt arial">----- Original Message -----</div> <div style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><b>From:</b> <a href="mailto:gnewell@ameritech.net" title="gnewell@ameritech.net">Greg Newell</a></div> <div style="FONT: 10pt arial"><b>To:</b> <a href="mailto:pianotech@ptg.org" title="pianotech@ptg.org">pianotech@ptg.org</a></div> <div style="FONT: 10pt arial"><b>Sent:</b> January 15, 2002 3:56 PM</div> <div style="FONT: 10pt arial"><b>Subject:</b> Re: my own Soundboard</div>  Thanks Del. I was still talking about edge gluing. I would not advocate joining two pieces end to end in a soundboard situation. Never crossed my mind. </blockquote> <font color="#000080">Why not? I'm planning on doing it on a piano I'm remanufacturing for myself. It's been done quite successfully in the past. I'll not be using a finger joint, however. I haven't quite decided what to use.</font>   <blockquote style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000080 2px solid; MARGIN-RIGHT: 0px">Has anyone ever tried gluing up 2 boards first, then adding one at a time until the desired panel size is achieved?</blockquote> <font color="#000080">We glue up sub-panels that are less than 24" wide (so we can still run them through our thickness planer) and then glue up the final panel.</font> <font color="#000080">Once you get started you will undoubtedly come up with your own ideas. There is no one 'right' way to do this stuff. Just a bunch of acceptable to good ways.</font> <font color="#000080">Del</font> <blockquote style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000080 2px solid; MARGIN-RIGHT: 0px"> </blockquote> </blockquote> </blockquote> <p>-- <br>Greg Newell <br><A HREF="mailto:gnewell@ameritech.net">mailto:gnewell@ameritech.net</A> <br>  </body> </html>