<html>
<body>
Terry, <br><br>
I think these are his two posts! <br><br>
<font size=2>Terry said: <br>
>"</font>Rebuilding an old (1900) Knabe grand backaction. The
darn flanges are <br>
>glued and screwed to the rail! I was surprised to find no sandpaper
on <br>
>the rail. I'll be doing some repining, etc. Regarding the flanges
glued <br>
>to the rail, what have folks found to be a good procedure to get this
<br>
>situation back up to snuff?<br>
><br>
>Also, what amount of friction is recommended for the back action
flanges <br>
>and the thingee that has the sostenuto activator thingee on it (what
are <br>
>the proper terms...?).<br>
><br>
>Thanks.<br><br>
Date: Sat, 2 Oct 2004<br><br>
Terry,<br>
I've found the following to work rather well: While the flanges are still
attached to the rail, center punch and drill for the appropriate flange
screws. Then remove the flanges. I prefer to put some moisture (just a
little) and heat to them. They'll pop off fairly well with a little
coaxing with a chisel. Clean up the rail and add sandpaper strips
w/appropriate holes punched. I like to attach the sandpaper with cold
hide glue as it gives you a sufficient amount of time to get everything
lined up and it doesn't leave lumps/bubbles in the sandpaper. (less
traveling needed, but there will be some.)<br><br>
<font size=2>Most of these do not have "damper barrels", so I
add them. a simple jig for the drill press will get that job done. Drill
for a tight fit and press them in with a punch in the drill press after
the holes have been drilled. Sure will make puttin' em in a lot
easier.<br><br>
</font>BTW, the thingee you are wondering about terminology-wise, is
called the Top Flange.<G> I like to use the specs. from the olde
Steinway manual. Without looking, I recall the Top Flange is <br>
1-3 grams and the Lever is 3-5 grams. Hope that helps.<br><br>
Best Regards,<br>
<font size=2>Joe Garrett, R.P.T.<br>
Captain, Tool Police<br>
Squares <br><br>
<br>
</font>At 04:43 PM 10/3/04, you wrote:<br>
<blockquote type=cite class=cite cite=""><font face="arial" size=2>Joe,
you bad boy - you type new subject titles, so I don't know exactly what
you are responding to. Bottom line: You say you forgot to add .........
but I can't find the original response to my post.<br>
</font> <br>
<font face="arial" size=2>......And I do so value your
input........<br>
</font> <br>
<font face="arial" size=2>Terry Farrell<br>
</font>
<dl>
<dd>----- Original Message ----- <br>
<dd>From:</b> <a href="mailto:joegarrett@earthlink.net">Joe Garrett</a>
<br>
<dd>To:</b> <a href="mailto:pianotech@ptg.org">pianotech</a> <br>
<dd>Sent:</b> Sunday, October 03, 2004 2:29 AM<br>
<dd>Subject:</b> Re: Olde Knabe Back Action<br><br>
<dd><font face="arial" size=2>Terry,<br>
<dd>I forgot to add: Most of these do not have "damper barrels", so I add them. a simple jig for the drill press will get that job done. Drill for a tight fit and press them in with a punch in the drill press after the holes have been drilled. Sure will make puttin' em in a lot easier.<br>
<dd>Best Regards,<br>
<dd>Joe Garrett, R.P.T.<br>
<dd>Captain, Tool Police<br>
<dd>Squares R I<br>
</font>
<dd> <br>
<dd><font face="arial" size=2>P.S.<br>
<dd>Since we didn't get a story of devastation, I assume your plywood shutters held.</font></blockquote>
</dl><font face="arial"><br>
Avery </font></body>
</html>