<html>
<body>
<font size=3><br>
Hi Phil & Horace,<br>
Assuming you have good sound board crown and correct bearing.<br><br>
Once the older
CF111's start to get Capo bar grooves the sustain tends to drop quite a
bit in this register. Drop the tension on two notes so you can
thread a strip of Emery cloth between the Capo and strings, shoe shine
the capo bar to remove the grooves, pull back up to tension and check the
sustain again. I think you will find an improvement.<br><br>
Lift the strings so there is a lower amount of forward duplex
bleed, tap the bridge pins to make sure they are secure, and the
strings are well seated. This will improve sustain.<br><br>
Make sure that all perimeter plate bolts are secure. Hammer
shape?????? Hammer fitting???? Glide bolts are critical
on this piano for optimum sustain and power.<br><br>
What is the hammer flange centre pinning Like? 4 gms of friction is
optimum. What is the let off and drop Like?<br><br>
The new CF111 hammers are made from Wurzen Felt and will produce much
better sustain. A World of difference from the old style
hammers.<br><br>
Should give you some food for thought.<br><br>
Regards Roger<br><br>
<br><br>
At 01:10 AM 3/13/2005, you wrote:<br><br>
<blockquote type=cite class=cite cite="">Hi, Phil,<br><br>
Assuming that you have already done the normal tapping of strings &
etc. type stuff - what do the strings sound like when plucked as opposed
to when struck by the hammer? That is, how much sustain do you get
one, relative to the other. If the sustain is consistent,
good/bad/etc aside, then the problem is quite probably the hammer(s)...at
least in that section.<br><br>
Also assuming that these are stock CFIII hammers, they really do not like
much in the way of liquids; and respond much better to quality shaping
and judicious needlework to develop tone. (The techniques are much
more like working on Bechstein or Bluthner than a North American
instrument. Various folks have written about approaches.) If,
however, they have been over needled across the crown (a growing
problem), either be pleased that you can pass this work back to someone
else or try to sell a new set of hammers. Since you said
"CFIII" and not "CFIIIs", this sounds like an older
instrument which might well be ready for a number of things.<br><br>
I'd be interested in what you find with some further
diagnostics.<br><br>
Best.<br><br>
Horace<br><br>
<br>
At 07:47 PM 3/12/2005, you wrote:<br>
<blockquote type=cite class=cite cite="">I am caring for one presently,
and from G#5 to about D6 is noticeably lacking in sustain of any
kind..almost like the damper is still on the strings. There is good tone,
with no sustain.<br><br>
Is there something I can do for these few notes to blend them in
better?<br><br>
The tech that normally has this piano in his possession does not like
liquids..and I'm not sure this is really a hammer problem since there is
good tone, but no sustain.<br><br>
Any ideas?<br><br>
Thanks,<br>
-Phil Bondi(Fl)<br><br>
_______________________________________________<br>
pianotech list info:
<a href="https://www.moypiano.com/resources/#archives" eudora="autourl">
https://www.moypiano.com/resources/#archives</a></blockquote><br>
_______________________________________________<br>
pianotech list info:
<a href="https://www.moypiano.com/resources/#archives" eudora="autourl">
https://www.moypiano.com/resources/#archives</a><br>
</font></blockquote></body>
</html>