<html>
<body>
Ross, <br><br>
I totally disagree! How else are you going to get them out. Do it slow,
and MUCH more <br>
heat builds up!<br><br>
Avery <br><br>
At 01:08 PM 9/8/05, you wrote:<br>
<blockquote type=cite class=cite cite="">If you spin tuning pins out,
you're going to scorch the holes in the block. You don't want
that.<br>
Ross White<br>
<dl>
<dd>----- Original Message ----- <br>
<dd>From:</b> <a href="mailto:pianotech@a440piano.net">William R.
Monroe</a> <br>
<dd>To:</b> <a href="mailto:pianotech@ptg.org">Pianotech</a> <br>
<dd>Sent:</b> Sunday, September 04, 2005 7:39 PM<br>
<dd>Subject:</b> Re: Removing tuning pins with the Milwaukee
Drill<br><br>
<dd>Joe,<br><br>
<dd>So, does this imply that the friction that generates the heat simply
doesn't<br>
<dd>have enough time to build up, vs. the slow removal, which may be
slow, but<br>
<dd>long and drawn out, consequently producing more heat?<br><br>
<dd>Interesting......<br><br>
<dd>Also, tried to email you about the keytop thing, but got
rejected. Anyway,<br>
<dd>I'll await receiving the keytop being sent to me first, and if it
doesn't<br>
<dd>work, I'll let you know. And, thanks.<br><br>
<dd>Respectfully,<br>
<dd>William R. Monroe<br><br>
<br><br>
<dd>----- Original Message ----- <br>
<dd>From: "Joe Garrett"
<<a href="mailto:joegarrett@earthlink.net">joegarrett@earthlink.net</a>
><br>
<dd>To: "pianotech"
<<a href="mailto:pianotech@ptg.org">pianotech@ptg.org</a>><br>
<dd>Sent: Sunday, September 04, 2005 9:12 PM<br>
<dd>Subject: Removing tuning pins with the Milwaukee Drill<br><br>
<br>
<dd>Terry Peterson said: "I also would like to get opinions as to
how fast, slow<br>
<dd>to remove them to<br>
<dd>avoid over-heating and/or scortching the pin block. I know the pins
WILL get<br>
<dd>hot no matter what, (I tested this by using the very lowest rpm
possible<br>
<dd>without stalling) but it seems to me that the main thing to avoid
is<br>
<dd>"spinning" the pin in place when/if it stops rising outward
during removal.<br>
<dd>I try to use lowest rpms to remove each pin, then releasing trigger
when<br>
<dd>it's almost out, letting the drill slow to a stop at which point the
pin<br>
<dd>drops out...ideally. thoughts?<br><br>
<dd>Terry,<br>
<dd>An interesting experiment: 1. Remove a tuning pin with a Brace and
Bit;<br>
<dd>immediately test it for heat. (it will be hottern' hell a first
touch.) 2.<br>
<dd>Remove a tuning pin with a Reversible Drill as slow as it will go.
Test it<br>
<dd>for heat. (it will be hot and getting hotter.) 3. Remove a tuning pin
with a<br>
<dd>Reversible drill running at/or around 600 RPM. Test it for heat. (It
will<br>
<dd>only be warm, but will heat up rapidly as you hold
it.DAMHIK!<G>) This<br>
<dd>phenomenon is kinda like Microwaving a spud.<G> The answer is
spin them out<br>
<dd>as fast as you feel comfortable with. I usually remove a whole set in
around<br>
<dd>15-20 minutes, using my 40 year old Wen Reversible
Drill.<G><br>
<dd>(It too, will spin the shop, if'n ya ain't careful!)<br>
<dd>Regards,<br>
<dd>Joe Garrett, R.P.T.<br>
<dd>Captain, Tool Police<br>
<dd>Squares R I<br><br>
<br>
<dd>_______________________________________________<br>
<dd>pianotech list info:
<a href="https://www.moypiano.com/resources/#archives">
https://www.moypiano.com/resources/#archives</a><br>
</dl></blockquote></body>
</html>