<html>
<!-- BEGIN WEBMAIL STATIONERY -->
<head>
<META HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=us-ascii">
<meta name=Generator content="Microsoft Word 10 (filtered)">
<style>
<!--
/* Font Definitions */
@font-face
{font-family:Tahoma;
panose-1:2 11 6 4 3 5 4 4 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:12.0pt;
font-family:"Times New Roman";}
a:link, span.MsoHyperlink
{color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{color:purple;
text-decoration:underline;}
span.EmailStyle17
{font-family:Arial;
color:navy;}
@page Section1
{size:8.5in 11.0in;
margin:1.0in 1.25in 1.0in 1.25in;}
div.Section1
{page:Section1;}
-->
</style>
</head>
<body lang=EN-US link=blue vlink=purple>
<div class=Section1>
<p class=MsoNormal><font size=2 color=navy face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:navy'><!-- WEBMAIL STATIONERY noneset -->Hi
Rick,</span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:navy'> </span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:navy'>For easing keys, I like to be just at or
slightly below boiling. For setting, I flick a drop of water on the broach. If
the water sits there, raise the temp. If it rapidly boils off, lower the temp.
You just have to find the crossover point, and mark the dial. As a safety, I
test it occasionally. </span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:navy'> </span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:navy'>Jerry Cohen, RPT</span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:navy'>NJ Chapter</span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span style='font-size:
10.0pt;font-family:Arial;color:navy'> </span></font></p>
<p class=MsoNormal style='margin-left:.5in'><font size=2 face=Tahoma><span
style='font-size:10.0pt;font-family:Tahoma'>-----Original Message-----<br>
<b><span style='font-weight:bold'>From:</span></b> pianotech-bounces@ptg.org
[mailto:pianotech-bounces@ptg.org] <b><span style='font-weight:bold'>On Behalf
Of </span></b>richard.ucci@att.net<br>
<b><span style='font-weight:bold'>Sent:</span></b> Sunday, March 06, 2005 1:12
PM<br>
<b><span style='font-weight:bold'>To:</span></b> pianotech@ptg.org<br>
<b><span style='font-weight:bold'>Subject:</span></b> temp.setting</span></font></p>
<p class=MsoNormal style='margin-left:.5in'><font size=3 face="Times New Roman"><span
style='font-size:12.0pt'> </span></font></p>
<div>
<p class=MsoNormal style='margin-left:.5in'><font size=3 face="Times New Roman"><span
style='font-size:12.0pt'>Hi folks,</span></font></p>
</div>
<div>
<p class=MsoNormal style='margin-left:.5in'><font size=3 face="Times New Roman"><span
style='font-size:12.0pt'>Just ordered the temp.control unit for soldering iron
tool used in key bushing easing etc. My question is, how to set the control so
as to not melt aluminum pieces, and what is the best setting for key easing?</span></font></p>
</div>
<div>
<p class=MsoNormal style='margin-left:.5in'><font size=3 face="Times New Roman"><span
style='font-size:12.0pt'> </span></font></p>
</div>
<div>
<p class=MsoNormal style='margin-left:.5in'><font size=3 face="Times New Roman"><span
style='font-size:12.0pt'>Thanks,</span></font></p>
</div>
<div>
<p class=MsoNormal style='margin-left:.5in'><font size=3 face="Times New Roman"><span
style='font-size:12.0pt'>Rick Ucci/Ucci Piano</span></font></p>
</div>
</div>
<!-- END WEBMAIL STATIONERY -->
</body>
</html>