<HTML><HEAD> <META content="MSHTML 6.00.2715.400" name=GENERATOR></HEAD> <BODY> <DIV><FONT face="MS Sans Serif" size=2>I think there woud be a noise issue.  Any material that would not be subject to compression over time would rattle at the balance rail. </FONT></DIV> <DIV> </DIV> <DIV><FONT face="MS Sans Serif" size=2> <DIV>David Love</DIV> <DIV><A href="mailto:davidlovepianos@earthlink.net">davidlovepianos@earthlink.net</A></DIV> <DIV> </DIV></FONT></DIV> <DIV> </DIV> <BLOCKQUOTE style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid"> <DIV style="FONT: 10pt Arial">----- Original Message ----- </DIV> <DIV style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B> <A title=hullfam5@yahoo.com href="mailto:hullfam5@yahoo.com">Bob Hull</A> </DIV> <DIV style="FONT: 10pt arial"><B>To: </B><A title=pianotech@ptg.org href="mailto:pianotech@ptg.org">Pianotech</A></DIV> <DIV style="FONT: 10pt arial"><B>Sent:</B> 5/3/2003 8:42:48 PM </DIV> <DIV style="FONT: 10pt arial"><B>Subject:</B> Re: New keyboard design (was Re: Key Leads and Inertia)</DIV> <DIV><BR></DIV><FONT size=2> <DIV>Thinking about wooden piano parts such as keys and their inconsistencies as well as balance rails which together create a situation in which we have to compensate by shimming with punchings in order to create the same key height for each key...  Couldn't a composite material be made that was machined or molded within strict tolerances so as to eliminate the need for leveling keys with punchings?  </DIV> <DIV> </DIV> <DIV>What about the type of graphite composites that are used in tennis rackets?  If this material was not affected by humidity and was very resisitant to wear, then used for the balance rail and the keys would that eliminate our key leveling requirements?  Are any paper punchings required on electronic keyboards to level their keys?   However, the key must not feel cheap like an electronic keyboard.   Other parts are being successfully made from alternative materials.   We have to shim these instruments that may cost up to $80,000 or so with little pieces of paper?  How high tech can we get? </DIV> <DIV> </DIV> <DIV>Bob Hull<BR><BR><B><I>Phillip Ford <fordpiano@earthlink.net></I></B> wrote:</DIV> <BLOCKQUOTE style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #1010ff 2px solid">> At 05:51 PM 5/1/03 , you wrote:<BR>>Frankly, I think that some extrudeed, lightweight<BR>>aluminum key, basically a shell buttressed with<BR>>reinforcement along stress lines to stiffen it, would<BR>>be FAR better than the 16th Century technology we are<BR>>dealing with! And it should be hinged on a lateral<BR>>pin ( at the bottom, on a pivotable plate ) to<BR>>eliminate all "wobble". And weights ( not poisonous<BR>>leads, either! ) could be affixed to the inside with<BR>>bolts and lock washers along an adjustable track for<BR>>exact balance.<BR>> Thump<BR><BR>These all sound like excellent ideas. While you're at it could you incorporate something into your design so that I can level the keys without putting paper punchings under the keys (talk about your 16th century technology)?<BR><BR>Phil F<BR><BR>_______________________________________________<BR!>pianotech list info: https://www.moypiano.com/resources/#archives</BLOCKQUOTE> <P> <HR SIZE=1> Do you Yahoo!?<BR><A href="http://us.rd.yahoo.com/search/mailsig/*http://search.yahoo.com">The New Yahoo! Search</A> - Faster. Easier. Bingo.</FONT></BLOCKQUOTE></BODY></HTML>