<HTML><HEAD></HEAD>
<BODY style="BORDER-TOP-STYLE: none; BORDER-RIGHT-STYLE: none; BORDER=
-LEFT-STYLE: none; BORDER-BOTTOM-STYLE: none">
<P><BR>That must be a Brazilian piano...;-]</P>
<P><BR>David Ilvedson, RPT<BR>Pacifica, California<BR><BR><BR><BR></P>
<DIV style="PADDING-RIGHT: 5px; PADDING-LEFT: 5px; PADDING-BOTTOM: 5p=
x; BORDER-LEFT: #000000 3px solid; PADDING-TOP: 5px">
<HR>
Original message<BR>From: pianotune05@comcast.net<BR>To: Pianotech <PIA=
NOTECH@PTG.ORG><BR>Received: 1/4/2006 6:13:47 PM<BR>Subject: Re: Tuning=
Standard<BR><BR>
<DIV align=left><FONT face="Arial, Helvetica, sans-serif">Hi again =
everyone,</FONT></DIV>
<DIV><FONT face=Arial>I wish this piano I did today was only a 1/2 st=
ep off. It was so off that the a4 didn' t even sound like an a wh=
en first played. I hope I did the pitch raise right. I raised and=
tuned at the same time. Next time I'm going to just match a440 and get=
the notes up to as close as possibel then actually tune it. Woul=
d that work?</FONT></DIV>
<DIV><FONT face=Arial>Marshall</FONT></DIV>
<DIV> </DIV>
<BLOCKQUOTE style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: =
#1010ff 2px solid">-------------- Original message -------------- <BR>F=
rom: David Vanderhoofven <david@vanderpiano.com> <BR><BR>> Hi =
Arlie, <BR>> <BR>> Short answer, and sorry about the lack of time=
for a full answer. <BR>> <BR>> 1. Technicians who don't know how=
to do pitch raises or how to sell pitch <BR>> raises. <BR>> 2. M=
usicians who don't care that their piano is 1/2 step flat and/or don't =
<BR>> want to pay for the pitch raise. <BR>> 3. Pianos with extre=
me rust and the technician is afraid of replacing <BR>> broken strin=
gs <BR>> 4 Pianos with extreme rust and the customer doesn't want to=
pay for <BR>> replacing broken strings <BR>> 5. Worn out, moth-e=
aten, rusted out hulks that have received almost no <BR>> service an=
d the cost of the pitch raise would be more than the value of the <BR>&=
gt; piano. <BR>> 6. Structural damage to the piano and the piano ! c=
ouldn't take the extra <BR>> tension on the strings without serious =
damage. <BR>> <BR>> Must my 2 cents: A piano that is 1/2 step fla=
t is not suited for use by a <BR>> musician or student. A piano need=
s to be at the correct pitch for <BR>> ear-training, music lessons, =
performances and playing with other musical <BR>> instruments or rec=
ordings. It doesn't make sense to me to leave a piano <BR>> 1/2 step=
flat unless the client is unwilling or unable to pay for the pitch <BR=
>> correction. And if the customer is unwilling to pay for the pitch=
<BR>> correction that is necessary, they are also unlikely to pay f=
or any other <BR>> needed service the piano needs. <BR>> <BR>>=
Just some ideas off of the top of my head. <BR>> Sincerely, <BR>>=
; <BR>> David A. Vanderhoofven <BR>> Registered Piano Technician =
<BR>> Joplin, MO <BR>> <BR>> At 12:14 PM 1/4/2006, you wrote: =
<BR>> >A friend in Brazil has been talking to me about the ! poss=
ibility of <BR>> >beginning tuning, and I'd be glad to help out. =
But she says that <BR>> >there pianos are generally tuned 1/2 ste=
p flat. I'm curious about <BR>> >that. Does anyone know why that =
might be? Because of that, she says <BR>> >they have mostly limit=
ed themselves to keyboards to avoid the obvious <BR>> >pitch/tran=
sposing challenges. <BR>> > <BR>> >Arlie Rauch <BR>> >=
;Glendive, MT <BR>> >____________________________________________=
___ <BR>> >pianotech list info: http://www.ptg.org/mailman/listin=
fo/pianotech <BR>> <BR>> ________________________________________=
_______ <BR>> pianotech list info: http://www.ptg.org/mailman/listin=
fo/pianotech </BLOCKQUOTE></DIV></BODY></HTML>