<HTML style="FONT-SIZE: x-small; FONT-FAMILY: MS Sans Serif"><HEAD> <META charset=US-ASCII http-equiv=Content-Type content="text/html; charset=US-ASCII"> <META content="MSHTML 6.00.2800.1400" name=GENERATOR></HEAD> <BODY style="FONT-SIZE: 10pt; FONT-FAMILY: Arial; BACKGROUND-COLOR: #ffffff"> <DIV><FONT face="MS Sans Serif">Dale:</FONT></DIV> <DIV><FONT face="MS Sans Serif"></FONT> </DIV> <DIV><FONT face="MS Sans Serif">If you are using my design for the carriage on a Router table you will have to increase the height to accomodate the hammer tail clearing the table.  I made that one for a Dremel table which is much narrower and the tail of the hammer hangs over the edge of the table.  </FONT></DIV> <DIV> </DIV> <DIV> <DIV>David Love</DIV> <DIV><A href="mailto:davidlovepianos@earthlink.net">davidlovepianos@earthlink.net</A></DIV> <DIV> </DIV></DIV> <DIV> </DIV> <BLOCKQUOTE style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid"> <DIV style="FONT: 10pt Arial">----- Original Message ----- </DIV> <DIV style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B> <A title=Erwinspiano@aol.com href="mailto:Erwinspiano@aol.com"></A></DIV> <DIV style="FONT: 10pt arial"><B>To: </B><A title=pianotech@ptg.org href="mailto:pianotech@ptg.org">pianotech@ptg.org</A></DIV> <DIV style="FONT: 10pt arial"><B>Sent:</B> 5/29/2004 8:41:18 AM </DIV> <DIV style="FONT: 10pt arial"><B>Subject:</B> relocating knuckles. --Tooling</DIV> <DIV><BR></DIV><FONT size=2> <DIV>      <FONT size=3>  </FONT></DIV> <DIV><FONT size=3>  List</FONT></DIV> <DIV><FONT size=3>  After our posts on this subject I found the parts available to do this. I ordered a cobalt double end mill from MSC part no.01714054 at 800-645-7270. $20.00 bucks. It has a 3/8" shaft & a .078 cutting ends. I thought the shaft size would be a problem but I discovered that a collet is made for a 1/2 router to adapt to it. I found this at Nordic specialty tools in Turlock ,Ca .The Part no is 65 at 209-634-9015. These folks will make custom router bits</FONT></DIV> <DIV><FONT size=3>  The guy at MSC also suggested a slotting saw (1&7/8") to run on the router & I cringed and said I like my fingers ,no thanks.</FONT></DIV> <DIV><FONT size=3>   Thanks to David love for his picture of his shank carraige. I'll post back the results after I get set up.</FONT></DIV> <DIV><FONT size=3>  Dale</FONT></DIV> <DIV><FONT size=3>  </FONT></DIV> <DIV> </DIV> <DIV> </DIV> <DIV><FONT lang=0 face=Arial size=2 PTSIZE="10" FAMILY="SANSSERIF">Erwins Pianos Restorations <BR>4721 Parker Rd.<BR>Modesto, Ca 95357<BR>209-577-8397<BR>Rebuilt Steinway , Mason &Hamlin Sales<BR>www.Erwinspiano.com</FONT></DIV></FONT></BLOCKQUOTE></BODY></HTML>