<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML style="FONT-SIZE: x-small; FONT-FAMILY: MS Sans Serif"><HEAD>
<META http-equiv=Content-Type content="text/html; charset=iso-8859-1">
<META content="MSHTML 6.00.2900.2722" name=GENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY bgColor=#ffffff>
<DIV><STRONG><FONT face=Arial size=3>Definitely, something we have all seen lots 
of times.</FONT></STRONG></DIV>
<DIV><STRONG><FONT face=Arial size=3>Good fix. I will certainly give it a go, 
next time.</FONT></STRONG></DIV>
<DIV><STRONG><FONT face=Arial size=3>I have always used the brass end pieces 
from the supply companies, previously.</FONT></STRONG></DIV>
<DIV>John M. Ross<BR>Windsor, Nova Scotia, Canada<BR><A 
href="mailto:jrpiano@win.eastlink.ca">jrpiano@win.eastlink.ca</A></DIV>
<BLOCKQUOTE 
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
  <DIV style="FONT: 10pt arial">----- Original Message ----- </DIV>
  <DIV 
  style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B> 
  <A title=tune4u@earthlink.net href="mailto:tune4u@earthlink.net">Alan 
  Barnard</A> </DIV>
  <DIV style="FONT: 10pt arial"><B>To:</B> <A title=pianotech@ptg.org 
  href="mailto:pianotech@ptg.org">Pianotech</A> </DIV>
  <DIV style="FONT: 10pt arial"><B>Sent:</B> Friday, August 26, 2005 2:24 
  PM</DIV>
  <DIV style="FONT: 10pt arial"><B>Subject:</B> Common Problem, Simple Repair 
  Idea</DIV>
  <DIV><BR></DIV>
  <P>
  <DIV>Photo: "Corner Damage"</DIV>
  <DIV>This corner, hinge-screw damage is all too common in older consoles and 
  spinets, where keeping the cost of repair on the low side is usually 
  necessary.</DIV>
  <DIV>&nbsp;</DIV>
  <DIV>Photo: "Wax Paper Dam"</DIV>
  <DIV>I drilled out the old screw hole to make it larger and cylindrical. Then 
  epoxied in tight-fitting pieces of hardwood dowel. When that cured, I trimmed 
  the dowel and used wax paper to make a dam to keep epoxy where it belongs. 
  (Thank you Dampp-Chaser for the handy push pins.)</DIV>
  <DIV>&nbsp;</DIV>
  <DIV>Photo: "Corner Repaired"</DIV>
  <DIV>I filled the damaged area with epoxy mixed with sawdust (made with a 
  drill), warmed it with a heat gun to thin it, and scraped it as level as 
  possible. This picture shows the corner after it has cured and been sanded 
  smooth.</DIV>
  <DIV>&nbsp;</DIV>
  <DIV>Photo: "Trimming Brass"</DIV>
  <DIV>These thin brass corners are available at Lowe's, or similar. Because the 
  depth was slightly more than the desk thickness, I used the sander to trim 
  "humps" on each side of the corner--they now appear as straight edges. I also 
  sanded the corner of the brass very thin and snipped it out with small wire 
  snippers. This allows the side that will be on the bottom of the desk to be 
  bent slightly to match the bevel of the desk bottom.</DIV>
  <DIV>&nbsp;</DIV>
  <DIV>Photos: "Final Look 1" and "Final Look 2"</DIV>
  <DIV>Used Dremmel to drill pilot holes for the screws holding the brass 
  (bottom screw NOT used since it would scratch the piano and make the desk sit 
  too high). Also drilled&nbsp;holes for the desk hinge&nbsp;screws. Both sides 
  had similar damage and were both repaired this way. The brass completely 
  covers all the damaged area, the epoxy, etc. It also provides a little 
  non-wood reinforcement for the hinge screws and, I think, looks kinda 
  spiffy.</DIV>
  <DIV>&nbsp;</DIV>
  <DIV>Anyway, the whole thing took less than an hour and was very satisfying; 
  thought I'd share.</DIV>
  <DIV>&nbsp;</DIV>
  <DIV>G'Day,</DIV>
  <DIV>&nbsp;</DIV>
  <DIV>Alan Barnard</DIV>
  <DIV>Salem, Missouri</DIV>
  <DIV>&nbsp;</DIV>
  <P></P>
  <P>
  <HR>

  <P></P>_______________________________________________<BR>pianotech list info: 
  https://www.moypiano.com/resources/#archives<BR></BLOCKQUOTE></BODY></HTML>