<HTML><FONT FACE=arial,helvetica><FONT  SIZE=2 FAMILY="SANSSERIF" FACE="Arial" LANG="0">In a message dated 1/13/2002 9:13:31 PM Pacific Standard Time, gnewell@ameritech.net writes:<BR>
<BR>
<BR>
<BLOCKQUOTE TYPE=CITE style="BORDER-LEFT: #0000ff 2px solid; MARGIN-LEFT: 5px; MARGIN-RIGHT: 0px; PADDING-LEFT: 5px">Subj:<B>Re: my own Soundboard </B><BR>
Date:1/13/2002 9:13:31 PM Pacific Standard Time<BR>
From:<A HREF="mailto:gnewell@ameritech.net">gnewell@ameritech.net</A><BR>
Reply-to:<A HREF="mailto:pianotech@ptg.org">pianotech@ptg.org</A><BR>
To:<A HREF="mailto:pianotech@ptg.org">pianotech@ptg.org</A><BR>
<I>Sent from the Internet </I><BR>
&nbsp; </FONT><FONT  COLOR="#000000" style="BACKGROUND-COLOR: #ffffff" SIZE=2 FAMILY="SANSSERIF" FACE="Arial" LANG="0"></BLOCKQUOTE><BR>
<BR>
</FONT><FONT  COLOR="#000000" style="BACKGROUND-COLOR: #ffffff" SIZE=2 FAMILY="SANSSERIF" FACE="Arial" LANG="0"><BR>
 Gregg<BR>
<BR>
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </FONT><FONT  COLOR="#000000" style="BACKGROUND-COLOR: #ffffff" SIZE=2 FAMILY="SANSSERIF" FACE="Arial" LANG="0">YES!&nbsp; Now we are on the same page , and I can see that you HAVE thought this part of it through more than a little bit.&nbsp; Setting up this kind of a jig is what ia needed to do the tongue and groove joints. You are correct about the jointer not being the tool for this as it has a nasty habit of putting a slight bow in the workyou were trying to make straight.<BR>
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Best<BR>
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Dale Erwin<BR>
</FONT><FONT  COLOR="#000000" style="BACKGROUND-COLOR: #ffffff" SIZE=2 FAMILY="SANSSERIF" FACE="Arial" LANG="0"><BR>
<BLOCKQUOTE TYPE=CITE style="BORDER-LEFT: #0000ff 2px solid; MARGIN-LEFT: 5px; MARGIN-RIGHT: 0px; PADDING-LEFT: 5px"><BR>
<BR>
Dale, <BR>
&nbsp;&nbsp;&nbsp; I think I get it now. You were talking about making a straight edge truly straight. Am I correct? For that I prefer to use a router. I know that most folks immediately think jointer but I've had very little luck as the ones I've been able to afford have had short beds and have left not so straight an edge and quite a lot of snipe. Since then I have taken to a 10' system I made from aluminum channel and a straight edge from aluminum box to have the router follow. A commercial type of this is made and called "Joint-a-bility" or something with very similar spelling. I have had good success making 2 boards wind up flush with each other over their entire length with no clamping whatsoever. I hope this is what you were talking about. If not, I am lost. Greg BTW - only one "g" at each end. Erwinspiano@AOL.COM wrote: <BR>
<BLOCKQUOTE TYPE=CITE style="BORDER-LEFT: #0000ff 2px solid; MARGIN-LEFT: 5px; MARGIN-RIGHT: 0px; PADDING-LEFT: 5px">&nbsp; </BLOCKQUOTE><BR>
</BLOCKQUOTE><BR>
<BR>
</FONT></HTML>