<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<html>
<head>
<META HTTP-EQUIV="Content-Type" CONTENT="text/html; =
charset=iso-8859-1">
<meta name=Generator content="Microsoft Word 10 (filtered)">
<style>
<!--
/* Font Definitions */
@font-face
        {font-family:Tahoma;
        panose-1:2 11 6 4 3 5 4 4 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
        {margin:0in;
        margin-bottom:.0001pt;
        font-size:12.0pt;
        font-family:"Times New Roman";}
a:link, span.MsoHyperlink
        {color:blue;
        text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
        {color:purple;
        text-decoration:underline;}
p
        {margin-right:0in;
        margin-left:0in;
        font-size:12.0pt;
        font-family:"Times New Roman";}
span.EmailStyle17
        {font-family:Arial;
        color:navy;}
@page Section1
        {size:8.5in 11.0in;
        margin:1.0in 1.25in 1.0in 1.25in;}
div.Section1
        {page:Section1;}
-->
</style>
</head>
<body bgcolor=white lang=EN-US link=blue vlink=purple>
<div class=Section1>
<p class=MsoNormal><font size=2 color=navy face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:navy'>Back the original pin off by 1 =
turn. Cut
a piece of wire a bit longer than you will need. Bend the hitch pin =
bend with
a round nose pliers. Put the wire on the hitch pin and pull the wire =
taught through
the agraffe or capo and cut the wire to length. Wind the string onto =
a dummy
pin with 2 ˝ turns. Remove the wire from the dummy pin and transfer =
it to the
original pin using needle nose pliers. Insert the becket and squeeze =
the coil to
get the wire fully inserted into the becket with a parallel =
pliers. Do the
same for the other end on the other pin. Pull to tension alternately =
with and
use a string lifter being careful that the wire doesn’t =
overlap. Squeeze
the wire at the becket again. Massage the wire along its length. =
Pull to
pitch. Massage some more. Pull to pitch. Grip the coil with =
parallel pliers
and turn the pliers in the direction of the coil. Pull to pitch. =
Do it all
again. Pull to pitch. Level the strings. Pull to pitch. =
Massage the wire at
the terminations to get the bend straightened. Pull to pitch. If =
the string
overlaps two different unisons, insert a mute between them until you can =
come
back to retune. If the string is two unisons on one note, tune them =
slightly sharp
and insert a mute between the one original string and the adjacent note =
so that
the two new strings are unmuted. They will drift flat, but will do so =
somewhat
together. Come back in 6-8 weeks to tweak them. Charge for all =
your visits. </span></font></p>
<p class=MsoNormal><font size=2 color=navy face=Arial><span =
style='font-size:
10.0pt;font-family:Arial;color:navy'> </span></font></p>
<div>
<p><font size=2 color=navy face="Times New Roman"><span =
style='font-size:10.0pt;
color:navy'>David Love<br>
davidlovepianos@comcast.net </span></font></p>
</div>
<p class=MsoNormal style='margin-left:.5in'><font size=2 =
face=Tahoma><span
style='font-size:10.0pt;font-family:Tahoma'>-----Original =
Message-----<br>
<b><span style='font-weight:bold'>From:</span></b> =
pianotech-bounces@ptg.org
[mailto:pianotech-bounces@ptg.org] <b><span =
style='font-weight:bold'>On Behalf
Of </span></b>Robert Finley<br>
<b><span style='font-weight:bold'>Sent:</span></b> Tuesday, September =
27, 2005
7:25 PM<br>
<b><span style='font-weight:bold'>To:</span></b> pianotech@ptg.org<br>
<b><span style='font-weight:bold'>Subject:</span></b> Problem =
Replacing Treble
String</span></font></p>
<p class=MsoNormal style='margin-left:.5in'><font size=3 =
face="Times New Roman"><span
style='font-size:12.0pt'> </span></font></p>
<div>
<p class=MsoNormal style='margin-left:.5in'><font size=2 =
face=Arial><span
style='font-size:10.0pt;font-family:Arial'>I am having a problem =
replacing
treble strings. The end of the wire always pops out of the hole in the =
tuning
pin when I try to put the first turn on. I have tried using the coil =
lifter to
hold the wire in place, but that didn't work. The diameter of the first
turn always becomes too large, and I can't make a neat first =
turn,
tight against the tuning pin. The result is that the end comes out of =
the hole
in the pin. The wire is so stiff and springy. The wire needs to be =
held
firrnly and tangential to the pin, but I am not sure how I can do this. =
Could
anyone suggest how I could overcome this problem? Thank you very much. =
</span></font></p>
</div>
<div>
<p class=MsoNormal style='margin-left:.5in'><font size=3 =
face="Times New Roman"><span
style='font-size:12.0pt'> </span></font></p>
</div>
<div>
<p class=MsoNormal style='margin-left:.5in'><font size=2 =
face=Arial><span
style='font-size:10.0pt;font-family:Arial'>Robert =
Finley</span></font></p>
</div>
</div>
</body>
</html>