<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN"> <HTML><HEAD> <META http-equiv=Content-Type content="text/html; charset=iso-8859-1"> <META content="MSHTML 6.00.2800.1126" name=GENERATOR> <STYLE></STYLE> </HEAD> <BODY bgColor=#ffffff> <DIV>Hi Clyde,</DIV> <DIV>Pipe clamps, not too expensive.</DIV> <DIV>Regards,</DIV> <DIV>John M. Ross<BR>Windsor, Nova Scotia, Canada<BR><A href="mailto:jrpiano@win.eastlink.ca">jrpiano@win.eastlink.ca</A></DIV> <BLOCKQUOTE dir=ltr style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px"> <DIV style="FONT: 10pt arial">----- Original Message ----- </DIV> <DIV style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B> <A title=cedel@supernet.com href="mailto:cedel@supernet.com">Clyde Hollinger</A> </DIV> <DIV style="FONT: 10pt arial"><B>To:</B> <A title=pianotech@ptg.org href="mailto:pianotech@ptg.org">Pianotech</A> </DIV> <DIV style="FONT: 10pt arial"><B>Sent:</B> Tuesday, January 21, 2003 8:03 AM</DIV> <DIV style="FONT: 10pt arial"><B>Subject:</B> Re: Piano Side</DIV> <DIV><BR></DIV>Don, <P>Thank you for a very helpful response.  I also have a client with a vertical piano in which the entire right side is separated from the strung back.  Since I wasn't quite sure how to go about doing the repair, and the customer didn't seem to want any extra expense, it hasn't been repaired yet. <P>I do have a question about the clamping you mention.  Can one actually buy clamps long enough to reach from one side of the piano to the other?  It seems to me that is what you would need.  Also, if they are available, I find it hard to part with the needed bucks to buy tools I may never need more than once. <P>Regards, <BR>Clyde Hollinger, RPT <P>Donald Mannino wrote: <BLOCKQUOTE TYPE="CITE"><FONT size=+0>Jack,</FONT> <P><FONT size=+0>It's OK with me if you declare the piano a total loss, and have them buy a new Kawai!</FONT> <P><FONT size=+0>:-)</FONT> <P><FONT size=+0>You will be better off removing the side and cleaning things up.  Take out the bottom board, action and keybed, remove the side from the back.</FONT> <P><FONT size=+0>After cleaning up splinters, carefully align the side again - it should be nearly flush with the rear facing panels top and bottom.  Match the other side exactly at the top - some models are even with the pinblock, others are not.  Once you get a good location, mark it all over the place to help get it back there.</FONT> <P><FONT size=+0>After taking the side off again, drill some small holes near the top and bottom, and install bridge pins point side out so that the point just barely sticks out the side (you can super glue or epoxy them into the holes).  Position the side panel according to your marks, and tap on it with a rubber mallet to leave marks in the side panel to help with alignment and keeping the side in position when clamping.  Then apply thick epoxy, put the panel on, and clamp it.</FONT> <P><FONT size=+0>Make sure the sides are parallel also - it could be easy to have the re-glued side angled out at the front if you only clamp at the back!  That would be a mess.</FONT> <P><FONT size=+0>Depending on the age of the piano, you might also want to call me at Kawai - if you are not comfortable doing this job, it could possibly be sent back to the factory in North Carolina and repaired there.  We did this with a UST-7 that had similar problems in a church a few years back.</FONT> <P><FONT size=+0>Don Mannino RPT</FONT> <BR><FONT size=+0>Kawai America</FONT> <BR><FONT size=+0>800-421-2177</FONT> <BR>  <P><FONT size=+0>At 04:53 PM 1/20/2003 -0800, you wrote:</FONT> <BLOCKQUOTE class=cite cite="" type="cite"><FONT face=arial><FONT size=-1>I am currently working on a Kawai. It is a school piano that the kids dropped off the stage. The piano is fine, except for the side. The glue has come undone. Question, Do I insert glue and clamp or do I take the whole side off and clean off old glue and reglue?</FONT></FONT> <BR><FONT face=arial><FONT size=-1>Also what kind of glue do I use?</FONT></FONT> <BR><FONT face=arial><FONT size=-1>Thanks</FONT></FONT> <BR><FONT face=arial><FONT size=-1>Jack</FONT></FONT></BLOCKQUOTE></BLOCKQUOTE></BLOCKQUOTE></BODY></HTML>